Freedom F-64 Programming Instructions
L
NAPCO Security Systems
Page 42
WI1502A 9/06
DISABLE PIR
NO
PRE-AWAY/STAY
060
LEARN PRIMARY
Y/N
LEARN SECONDARY
Y/N
CLEAR ALL
LEARNED TXS Y/N
DISPLAY
RF SS Y/N
DISPLAY
RF NOISE Y/N
Disable PIR
If
YES
is pressed, will disable the PIR as an intrusion detection device. Press
NO
to enable PIR.
Default is "NO" (enabled). Press
MENU
to continue or press
RESET
to exit.
Pre-AWAY / STAY
The
Pre-AWAY
/
STAY
period is the amount of time that the user has to complete the arming
sequence. The arming sequence starts with pressing the
STAY
or
AWAY
buttons, and ends
by closing the deadbolt. If the sequence is not completed, the system will remain in the previ-
ous state, or will be disarmed if a deadbolt is left open. Valid entries are 020 - 240 (seconds).
Press
ENTER
to move cursor to the left (press repeatedly to loop back), then press
YES
or
NO
to increment or decrement each digit. Default is "060" (60 seconds). Press
MENU
to
continue or press
RESET
to exit.
Learn Primary
Send command to the Touchpad's integral receiver module to learn the Primary transmitter ID. If
YES
is pressed, will display:
PRESS/RELEASE TAMPER SWITCH
. If learned successfully, displays:
PRIMARY TXMIT LEARNED – SS##
. If learned unsuccessfully, displays:
LEARN FAILED TRY
AGAIN? Y/N
. See WI1499 for full instructions for installing and learning transmitters. Not used
with the F-64TP-H Hardwired Touchpad. Press
NO
or
MENU
to continue or press
RESET
to
exit.
Learn Secondary
Send command to the Touchpad's integral receiver module to learn the Secondary ID. Be sure to
install the shunt on the Secondary transmitter address jumper to ensure the transmitter is identified
as the Secondary transmitter and not the Primary transmitter. Install a Secondary transmitter to
protect a second door that will be used only for
entry
or to disarm when armed Stay. If
YES
is
pressed, will display:
PRESS/RELEASE TAMPER SWITCH
. If learned successfully, displays:
SEC-
ONDARY TXMIT LEARNED – SS##
. If learned unsuccessfully, displays:
LEARN FAILED TRY
AGAIN? Y/N
. See WI1499 for full instructions for installing and learning transmitters. Not used
with the F-64TP-H Hardwired Touchpad. Press
NO
or
MENU
to continue or press
RESET
to
exit.
Clear All Learned TXS
Erase all learned transmitter ID's. If
YES
is pressed, displays:
PLEASE WAIT
. When complete
displays:
ALL TRANSMITTERS CLEARED
. If unsuccessful, displays:
XMITTER CLEAR FAILED
TRY AGAIN?
. See WI1499 for full instructions for installing and learning transmitters. Not used
with the F-64TP-H Hardwired Touchpad. Press
NO
or
MENU
to continue or press
RESET
to
exit.
Display RF SS
Press
YES
to display the signal strength of the enrolled transmitters. See
Display RF Noise
op-
tion below. Press
NO
or
MENU
to continue or press
RESET
to exit.
Display RF Noise
Indicates the ambient radio frequency noise on each of the enrolled transmitter frequencies.
Typical measurements are below 100. If this level is too close to the signal strength ("
Display
RF SS
" above) recorded for the Secondary transmitter, an additional F-64TP may be required
to be mounted near the Secondary transmitter. The
RF SS
should be at least 50 points higher
than the
RF NOISE
level. Press
YES
to display. Press
NO
or
MENU
to continue or press
RESET
to exit.
To
exit
Touchpad Configuration Mode, press
RESET
.
