NAL A3LA-RG User Manual Download

Page: 152 / 180

A3LA-RG Guide Version B

Document Number: 451-93156-009B

152 of 180

PPENDIX

NFORMATIVE

XAMPLES

The examples below are presented in two different formats. The format used in each example

has no significance. A single format will be used in a future revision of this document.

E.1 U

NIT

DENTIFICATION

When beginning to build a communication link, a general DTE application controlling the

A3LA-RG should confirm the type of Iridium device to which it is connected.

Table 11: Unit Identification

To A3LA-RG (from DTE)

To DTE (from A3LA-RG)

Description

AT+CGMI

Get manufacturer name

Iridium

AT+CGMM

Get model number

AT+CGMR

Get revision

Call processor version: <revision>

DSP version: <revision>

…

AT+CGSN

Get IMEI

300001000000000

E.2 S

ETTING THE

EFAULT

ONFIGURATION

The DTE sets the A3LA-RG’s default configuration to no flow control and SBD automatic

notifications enabled.

Table 12: Default Configuration

To A3LA-RG (from DTE)

To DTE (from A3LA-RG)

Description

AT&K0

Disable RTS/CTS flow control

Summary of Contents for A3LA-RG





















































































































































































Search results

Summary of Contents for A3LA-RG

Reviews:

Related manuals for A3LA-RG

Brands by name

Popular brands

NAL A3LA-RG, User Manual

Search results

Summary of Contents for A3LA-RG

Reviews:

Related manuals for A3LA-RG

Brands by name

Popular brands