NAL A3LA-RG User Manual Download Page 92

Page: 92 / 180

A3LA-RG Guide Version B

Document Number: 451-93156-009B

92 of 180



The MOMSN is maintained even after power cycle. Command Response:

0: The MOMSN was cleared successfully

1: An error occurred while clearing the MOMSN

B.90 +SBDS

–

HORT

URST

ATA

TATUS

Exec Command:

+SBDS

This command returns current state of the mobile originated and mobile terminated

buffers.

Command Response:

+SBDS: <MO flag>, <MOMSN>, <MT flag>, <MTMSN>

where:

<MO flag>: The MO flag indicates the existence of a message in the mobile originated

buffer. The response from the A3LA-RG is one of the following numeric codes:

0: No message in mobile originated buffer

1: Message in mobile originated buffer

<MOMSN>: The MOMSN identifies the sequence number that will be used during the

next mobile originated SBD session.

<MT Flag>: The MT flag indicates the existence of a message in the mobile terminated

buffer. The response from the A3LA-RG is one of the following numeric codes:

0: No message in mobile terminated buffer

1: Message in mobile terminated buffer

<MTMSN>: The MTMSN identifies the sequence number that was used in the most

recent mobile terminated SBD session. This value will be –1 if there is nothing in the

mobile terminated buffer.

B.91 +SBDTC

–

HORT

URST

ATA

RANSFER

UFFER TO

UFFER

Exec Command:

+SBDTC

Summary of Contents for A3LA-RG





















































































































































































Search results

Summary of Contents for A3LA-RG

Reviews:

Related manuals for A3LA-RG

Brands by name

Popular brands

NAL A3LA-RG, User Manual

Search results

Summary of Contents for A3LA-RG

Reviews:

Related manuals for A3LA-RG

Brands by name

Popular brands