NAL A3LA-RG User Manual Download

Page: 76 / 180

A3LA-RG Guide Version B

Document Number: 451-93156-009B

76 of 180

Test Command:

+CLVL=?

List the supported volume level settings. The response is in the form:

+CLVL: (supported <level>s)

B.67 +CMUT

–

UTE

ONTROL

Exec Command:

+CMUT=<n>

This command is used to enable and disable the uplink voice muting during a voice

call. <n> can take one of the following values:

0 mute off

1 mute on

Read Command:

+CMUT?

Query the current mute setting. The response is in the form:

+CMUT: <n>

Test Command:

+CMUT=?

List the supported mute settings. The response is in the form:

+CMUT: (supported <n>s)

B.68 +CRC

–

ELLULAR

ESULT

ODES

ExecSet Command:

+CRC=[<mode>]

Set the extended format of incoming data or voice call indication.

<mode> takes the following values:

0 Disable extended format (default)

1 Enable extended format

If extended format is enabled, the unsolicited result code +CRING: <type> is returned

by the A3LA-RG instead of RING, where <type> can be one of the following:

ASYNC

asynchronous transparent

SYNC

synchronous transparent

REL ASYNC

asynchronous non-transparent

REL SYNC synchronous non-transparent

Summary of Contents for A3LA-RG





















































































































































































Search results

Summary of Contents for A3LA-RG

Reviews:

Related manuals for A3LA-RG

Brands by name

Popular brands

NAL A3LA-RG, User Manual

Search results

Summary of Contents for A3LA-RG

Reviews:

Related manuals for A3LA-RG

Brands by name

Popular brands