Nahita LNB003 Instruction Manual Download Page 3

 

 

 

 

   

Prohibitions

 

1

 

Read this instruction manual before using the product. 

2

 

Do  not  put  volatile,  flammable  and  explosive  material  in  the  machine,  otherwise  could 
cause explosion or fire. 

3

 

Do not place the incubator in a place exposed to rain, moisture, or splashing, as this may 
result in electrical leakage, short circuit, or electric shock. 

4

 

Non-professional  persons  must  not  disassemble,  repair  or  modify  the  equipment, 
otherwise it may cause fire or electric shock to personnel due to improper operation. 

5

 

Do not damage the power plug or the power cord. If it is damaged, the power cord must 
be replaced. Otherwise, it may cause fire or electric shock. 

 

 

Recommendations 

 
1.

 

This equipment should install on the firm ground, otherwise could cause staff injury 

because of drop down of the equipment. 
2.

 

Please use the special power supply that indicated one the nameplate. This equipment must 

install  on  the  ground,  otherwise  could  cause  electric  shock  and  fire  because  of  electric 
leakage. 
3.

 

Do not touch the power plug with wet hands, otherwise there is a risk of electric shock. 

4.

 

Before any repair or maintenance is carried out, the power must be disconnected to prevent 

electric shock or injury. 
5.

 

Please wear gloves when repair and maintain the equipment in case of injury. 

6.

 

Do not to damage the power cord or use the non - specified power cord, do not connect the 

power  cord  in  the  middle  section  and  use  long  soft  wire,  otherwise  it  may  lead  to  electric 
shock or fire. 
7.

 

Do not remove the power plug during the operation, do not pull the power cord by pulling 

the power cord. 
8.

 

If you find that the equipment is running abnormally, unplug the power plug immediately 

and stop the equipment. 
9.

 

If  the  equipment  is  idle  for  a  long  time  in  the  unsupervised  area,  please  ensure  that  the 

equipment door is completely closed. 

 

Necessary considerations

 

 

 

Adjust the feet so that the equipment is installed horizontally, and all four feet should be 
close to the support surface. There must be no vacant or false. 

1.

 

Safety warning before operation

 

 

The following items could cause serious injury or death.   

The following items may cause personal injury,   

equipment damage and related property damage. 

 

The following items could cause staff injury   

or equipment.   

Summary of Contents for LNB003
















Reviews: