background image

  

29 of 31

www.NabcoEntrances.com 

GT1175 Slide Door Opus Control Wiring and Programming Manual

Rev. 8-11-21 

P/N C-00391

On GT-1175 Slide doors, the Optex OS-12C Module Infrared Beam is installed and wired at the NABCO factory. This unit is shipped 

complete with Emitter(s), Receiver(s) and a Control Box. Both the Emitter and Receiver are flush mounted on the inside, Slide door 

Jamb Tube and Sidelite Strike Stile, or both Strike Stiles, directly across from each other. The Rcvr/Emit are installed 21 inches from 

the floor. If deemed necessary, a second Rcvr/Emit may be installed 54 inches from the floor.
In the event a pedestrian or object crosses the threshold, breaking a beam, the beam controller will send a signal to the door control 

to hold the door open until the threshold is clear and the beam is restored.

DN 1879

SINGLE SLIDE DOOR

BI-PART SLIDE DOOR

Emit

Rcvr

Emit

Rcvr

Floor

21 inches

54 inches 

Floor

21 inches

54 inches 

Emit

Rcvr

Emit

Rcvr

Sidelite

Jamb

Tube

Sidelite

Sidelite

SECTION 11.11: Wiring a Card Reader, or secure Activation Device, to 1175

DN 2289

3

456

7

10

11

12

13

14

I/O Terminal 8-14

I/O Terminal 1-7

A en on:  Device must provide Normally Open, Dry Contacts (No Voltage).

1. Connect the Key Pad, Card Reader or Key Switches to Terminals 2 and 6 as shown.
2. Under INPUT SETTINGS, set INPUT SWL to ALL MODE ACTIVATION.
3. The Device will be enabled to ac vate the door regardless of which Rocker Switch Mode 

is selected (Auto, One Way, or Night).

a. The Device will not ac vate if the Switch is in the OFF posi on.

COM

N.C.

N.O.

Relay Output 3

KEY PAD OR CARD READER ON 

SECURE SIDE OF DOOR

(N.O. - DRY CONTACTS)

Summary of Contents for GYRO TECH GT-1175
































Reviews: