background image

 

1 of 32

Swing Door and Fold Door Opus Control 

Wiring and Programming 

Installation Manual

 

P/N C-00139  Rev 8-11-21

NABCO Entrances Inc.   S82 W18717 Gemini Drive   Muskego, Wisconsin 53150

Phone:  (877) 622-2694   Fax:  (888) 679-3319   www.nabcoentrances.com

NABCO hours of Operation:  Monday to Friday  8:00 a.m.- 4:30 p.m. (Central Time) 

•  Turn OFF all power to the Automatic Door if a Safety System is not working. 
•  Instruct the Owner to keep all power turned OFF until corrective action can be achieved 

by a NABCO trained technician. Failure to follow these practices may result in serious 

consequences.

•  NEVER leave a Door operating without all Safety detection systems operational.

WARNING

Table of Contents

CHAPTER 1: SAFETY

   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 3

CHAPTER 2: SCOPE

   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4

SECTION 2.1: To the Installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4

SECTION 2.2: Objective . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4

SECTION 2.3: Request a User Name/Password to gain access into the “myNABCO” portal . . . . . . . . . . . . . . . . . . . .

4

SECTION 2.4: QR Code Links . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4

CHAPTER 3: GETTING STARTED

   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 5

SECTION 3.1: Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5

SECTION 3.2: Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5

SECTION 3.3: General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5

SECTION 3.4: Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5

SECTION 3.5: Output Power Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6

SECTION 3.6: The Opus Control for Swing Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6

SECTION 3.7: Navigate with the Rotary Dial

   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6

SECTION 3.8: IO Terminal strips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
SECTION 3.9: Relay Output Terminal Strip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
SECTION 3.10: CAN Bus Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

CHAPTER 4: LCD CATEGORY SCREENS

   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 7

SECTION 4.1 Level One: Specification Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
SECTION 4.2 Level Two: Access Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
SECTION 4.3 Enter Passcode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
SECTION 4.4 Cancel Passcode or Reset to Default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
SECTION 4.5 Level Three and Four: Setting Category and Menu Items  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

CHAPTER 5: STROKE LEARNING (SWING AND FOLD DOORS)

   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 9

SECTION 5.1 Stroke Learning (YES)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
SECTION 5.2 Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

CHAPTER 6: SIMULTANEOUS PAIR, DOUBLE EGRESS, AND BI-FOLD DOORS

  .  .  .  .  .  .  .  .  .  .  .  .  . 

10

SECTION 6.1: Copy Data from Type 2 (Master Control) to Type 1 (Slave Control)  . . . . . . . . . . . . . . . . . . . . . . . . . . .

11

SECTION 6.2: Resetting a Type 2 Control back to a Type 1 Control  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11

SECTION 6.3: Customized Programming/Settings for (1) Control only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12

Summary of Contents for C-00139

































Reviews: