background image

12/1/2006 

22 

 

Default Gateway: Sets the IP default gateway address 
Default: 0.0.0.0  

 

IP DNS: Enables/Disables DNS client on the module 
Default: disable  

 

Pri DNS: Sets the Primary DNS IP address 
Default: 0.0.0.0  

 

Sec DNS: Sets the Secondary DNS IP address 
Default: 0.0.0.0  

 

DHCP Client: Enables/Disables DHCP Client 
Note:  

o

 

DHCP info parameters DHCP netmask, Gateway, DNS and DHCP server will be set if the module obtains IP address from DHCP server 
successfully. These cannot be modified.  

o

 

If DHCP Client fails to contact the DHCP Server, after a finite number of retries, initializes the eth0 with static ip address. It checks periodically 
and retries to obtain an IP address from a DHCP server  

Default: enable 

 

IP Address: If DHCP is disabled, sets the static IP address of the module. If DHCP is enabled, the ip address given by the DHCP server is displayed and its 
not configurable. 
Note:  

o

 

When the static ip address is modified, the browser gets redirected to new ip address. 

Default: 192.168.2.1  

 

TFTP: Enables/Disables TFTP Server. On enabling the TFTP Server, the network administrator can upload the firmware to the flash 
Notes: 
TFTP application is associated with "inetd" application 
Configuration change of TFTP service calls for a re-initialization of "inetd", eventually closes all the current session that are associated with "inetd" 
The other application(s) that are associated with "inetd" are Telnet Server 
Hence when enabling/disabling TFTP through a Telnet configuration, would terminate the current telnet sessions 
Default: enable  

 

TCP Keepalive: Sets the tcp keepalive timeout (minutes) value. This is used to terminate the TCP session if there is no traffic 
Default: 3 minutes  

 

Autodiscovery: Enables/Disables Auto-discovery to broadcast (MAC Level), the MAC-address, IP address and DHCP information to server port configured 
(default 1020) 
Default: enable  

 

Server Port: Sets the Auto Discovery Manager Server port 
Default: 1020  

 

Broadcast Timer: Auto-discovery packet granularity of periodic Broadcasting 
Default: 10 seconds  

 

AG Server: Starts the UDP server on port 526. Starts a Tcp server on port 599. Uses proprietary Multitech Asynchronous Gateway Protocol (AG).  

o

 

Discovery mechanism - UDP server responds with UDP unicast packet to the UDP broadcast packet from WinMCSI Port Redirector  

o

 

Status mechanism - TCP server responds to the Status Request packet from the WinMCSI Port Redirector Client  

Default: disable  

 

Auto Dialout: Enables/Disables Auto-Dialout feature globally on the module 
Default: enable  

 

Auto Dialin: Enables/Disables Auto-Dialin feature globally on the module 
Default: disable  

 

Telnet Configuration  

 

Telnet: Enables/Disables the Telnet Server used for Command Line Configuration. On disabling Telnet server, the administrator cannot configure the IP 
Module through Telnet. The only option is to connect through a terminal application over the Serial port 
Default: enable  

 

Telnet Port: Sets the telnet port used for Command Line Configuration 
Notes: 
Telnet application is associated with "inetd" application 
Modification to the telnet port calls for a re-initialization of "inetd". This inturn closes all the current session that are associated with "inetd" 
The other application(s) that are associated with "inetd" are TFTP Server. Hence, invoking this command would terminate the current telnet sessions 
Default: 23  

 

Escape Monitor: Enables/Disables ‘‘monitor’’ flag to scan escape sequence and switch to command mode during Manual dialout session 
Default: enable  

 

Escape String: Sets the escape string to be scanned during Manual Dialout session to switch to command mode 
Default: +++inet  

 
 
(continued…)
 

Summary of Contents for 102PC-SE









































Reviews: