47
M1.1.SL300U-SL300UM.NLFREN 28082018
EN
General precautions
The operator and the maintenance fitter are required to observe the prescriptions of safety regulation in force in the country of
installation of the lift.
•
Furthermore, the operator and maintenance fitter must:
- Always work in the stations specified and illustrated in this manual,
- Never remove or deactivate the guards and mechanical, electrical, or other types of safety devices,
- Read the safety notices placed on the machine and the safety information in this manual.
Risk and protection devices
• For optimal personal safety and safety of vehicles, observe the following regulations:
- Do not enter the safety and safety of vehicles is being lifted (Picture 7).
- Be sure to lift only approved vehicles, never exceed the specified carrying capacity, maximum height, and projection
(vehicle length and width).
- Make sure that there is no person on the platforms during up and down movements and during standing.
U
U
S
S
E
E
R
R
‟
‟
S
S
M
M
A
A
N
N
U
U
A
A
L
L
V
V
1
1
.
.
0
0
2
2
0
0
1
1
4
4
0
0
8
8
- 10 -
5. Safety notes
General precautions
The operator and the maintenance fitter are required to observe the prescriptions of safety regulation in
force in the country of installation of the lift.
Furthermore, the operator and maintenance fitter must:
-Always work in the stations specified and illustrated in this manual;
-Never remove or deactivate the guards and mechanical, electrical, or other types of safety devices;
-Read the safety notices placed on the machine and the safety information in this manual.
In the manual all safety notices are shown as follows:
Warning:
indicates following operations that are unsafe and can cause minor injury to persons and
damage the lift, the vehicle or other property.
Risk of electric shock:
a specific safety notice placed on the lift in areas where the risk of electric shock
is particularly high.
Risk and protection devices
For optimal personal safety and safety of vehicles, observe the following regulations:
-Do not enter the safety and safety of vehicles is being lifted. (
Picture 7
)
-Be sure to lift only approved vehicles, never exceed the specified carrying capacity, maximum height,
and projection (vehicle length and width);
-Make sure that there is no person on the platforms during up and down movements and during standing
Picture 8
Picture 9
Picture 7
Picture 8
Picture 9
General risks for lifting or descent
• The following safety equipments are used to protect over loading or the possibility of engine failure. In the condition of over
loading, the over-falling valve will open and directly return oil to the oil tank (Picture 8).
• Each bottom of oil cylinder is equipped with antiknock and locked valve (optional). When the oil pipe is burst in the circuit
of hydraulic pressure, the relevant antiknock and locked valve will work and limit the speediness of platform (Picture 9).
• Safety tooth and gear module are parts which guarantee the safety of personnel beneath the machine in failure condition
of other protections. So make sure the integrity of gear module and that the safety tooth has occluded completely (Picture
10). There is nothing abnormal should be left on the safety modules to prevent safety gear from occlude normally.
U
U
S
S
E
E
R
R
‟
‟
S
S
M
M
A
A
N
N
U
U
A
A
L
L
V
V
1
1
.
.
0
0
2
2
0
0
1
1
4
4
0
0
8
8
- 11 -
General risks for lifting or descent
The following safety equipments are used to protect over loading or the possibility of engine failure.
In the condition of over loading, the over-falling valve will open and directly return oil to the oil tank.
(
Picture 8
)
Each bottom of oil cylinder is equipped with antiknock and locked valve(
optional
). When the oil pipe is
burst in the circuit of hydraulic pressure, the relevant antiknock and locked valve will work and limit the
speediness of platform. (
Picture 9
)
Safety tooth and gear module are parts which guarantee the safety of personnel beneath the machine in
failure condition of other protections.
So make sure the integrity of gear module and that the safety tooth has occluded completely. (
Picture 10
)
There is nothing abnormal should be left on the safety modules to prevent safety gear from occlude
normally.
Picture 10
Risk for extrusion
During up and down operations, personnel leave the said area without following the rule and instruction.
During up and down operations, no person is admitted to work beneath the movable parts of the lift,
should work in the safe zone. (
Picture 9
)
Risk of impact
Before the operator begins up and down movements, make sure that there are no personnel inside the
danger zone. When, due to operational reasons, the lift is stopped at relatively low elevations (lower than
1.75m above the ground) personnel must be careful to avoid impact with parts of the machine not
marked with special colors. (
Picture 12
)
Picture 11
Picture 12
U
U
S
S
E
E
R
R
‟
‟
S
S
M
M
A
A
N
N
U
U
A
A
L
L
V
V
1
1
.
.
0
0
2
2
0
0
1
1
4
4
0
0
8
8
- 11 -
General risks for lifting or descent
The following safety equipments are used to protect over loading or the possibility of engine failure.
In the condition of over loading, the over-falling valve will open and directly return oil to the oil tank.
(
Picture 8
)
Each bottom of oil cylinder is equipped with antiknock and locked valve(
optional
). When the oil pipe is
burst in the circuit of hydraulic pressure, the relevant antiknock and locked valve will work and limit the
speediness of platform. (
Picture 9
)
Safety tooth and gear module are parts which guarantee the safety of personnel beneath the machine in
failure condition of other protections.
So make sure the integrity of gear module and that the safety tooth has occluded completely. (
Picture 10
)
There is nothing abnormal should be left on the safety modules to prevent safety gear from occlude
normally.
Picture 10
Risk for extrusion
During up and down operations, personnel leave the said area without following the rule and instruction.
During up and down operations, no person is admitted to work beneath the movable parts of the lift,
should work in the safe zone. (
Picture 9
)
Risk of impact
Before the operator begins up and down movements, make sure that there are no personnel inside the
danger zone. When, due to operational reasons, the lift is stopped at relatively low elevations (lower than
1.75m above the ground) personnel must be careful to avoid impact with parts of the machine not
marked with special colors. (
Picture 12
)
Picture 11
Picture 12
Picture 10
U
U
S
S
E
E
R
R
‟
‟
S
S
M
M
A
A
N
N
U
U
A
A
L
L
V
V
1
1
.
.
0
0
2
2
0
0
1
1
4
4
0
0
8
8
- 11 -
General risks for lifting or descent
The following safety equipments are used to protect over loading or the possibility of engine failure.
In the condition of over loading, the over-falling valve will open and directly return oil to the oil tank.
(
Picture 8
)
Each bottom of oil cylinder is equipped with antiknock and locked valve(
optional
). When the oil pipe is
burst in the circuit of hydraulic pressure, the relevant antiknock and locked valve will work and limit the
speediness of platform. (
Picture 9
)
Safety tooth and gear module are parts which guarantee the safety of personnel beneath the machine in
failure condition of other protections.
So make sure the integrity of gear module and that the safety tooth has occluded completely. (
Picture 10
)
There is nothing abnormal should be left on the safety modules to prevent safety gear from occlude
normally.
Picture 10
Risk for extrusion
During up and down operations, personnel leave the said area without following the rule and instruction.
During up and down operations, no person is admitted to work beneath the movable parts of the lift,
should work in the safe zone. (
Picture 9
)
Risk of impact
Before the operator begins up and down movements, make sure that there are no personnel inside the
danger zone. When, due to operational reasons, the lift is stopped at relatively low elevations (lower than
1.75m above the ground) personnel must be careful to avoid impact with parts of the machine not
marked with special colors. (
Picture 12
)
Picture 11
Picture 12
Picture 11
Picture 12
Risk for extrusion
• During up and down operations, personnel leave the said area without following the rule and instruction.
• During up and down operations, no person is admitted to work beneath the movable parts of the lift, should work in the
safe zone (Picture 11).
Risk of impact
• Before the operator begins up and down movements, make sure that there are no personnel inside the danger zone. When,
due to operational reasons, the lift is stopped at relatively low elevations (lower than 1.75 m above the ground) personnel
must be careful to avoid impact with parts of the machine not marked with special colours (Picture 12).
copyrighted
document
- all
rights
reserved
by
FBC
