Muton ValueJet VJ-1627MH Startup Manual Download Page 9

Page: 9 / 56

Assembling

Follow the procedure below to attach the stand to the printer.

[6]

Fasten the connector bar to the left stand in the same way as in Step 5.

[7]

Attach the waste fluid tank holder to the right stand using four screws.

[8]

Shake the stand to make sure that each part is firmly attached.

Procedure for attaching the stand

[1]

Turn the four adjusters as shown below to prevent the stand from

moving.

[2]

Insert the two transfer stays into the right and left transfer brackets, lift

the printer with four or more people and place it on the stand.

[3]

Remove the two transfer stays and fasten the printer to the stand

using eight butterfly screws.

• 1: Transfer stays

• 2: Stand

• 3: Butterfly screws

Stand (left)

Connector bar

Hexagon socket
head cap screws

Front

Stand (right)

Screws

Waste fluid tank holder

Stand

Adjusters

Stand

Transfer stay

Transfer bracket

Summary of Contents for ValueJet VJ-1627MH

























































Search results

Summary of Contents for ValueJet VJ-1627MH

Reviews:

Related manuals for ValueJet VJ-1627MH

Brands by name

Popular brands

Muton ValueJet VJ-1627MH, Startup Manual

Search results

Summary of Contents for ValueJet VJ-1627MH

Reviews:

Related manuals for ValueJet VJ-1627MH

Brands by name

Popular brands