Muton ValueJet VJ-1627MH Startup Manual Download Page 15 | Manualshive

Page: 15 / 56

background image

Assembling

15

Before printing on a rigid media, follow the steps below to install the media-feed tables.

Required items:

• Hexagonal spanner (supplied with the media-feed table)

• Level (supplied with the printer)

Attaching the media-feed table (optional)

Rear side procedure

[1]

Loosen the fixing levers on the right and left side of the rear. Set the

distance between the roll media holders wider than the roll media

width.

[2]

Check that the leveling screws on the left and right side of the table

are tightened.

Note

When fixing the leveling screws, hold the frame while pressuring the rubber foot, and

then turn the screw until it doesn’t turn any further.

[3]

Insert the positioning guide of Media-feed table into the square hole of Paper guide R.

Positioning guide

Square hole

«
...
13
14
15
16
17
...
»

Summary of Contents for ValueJet VJ-1627MH

























































Reviews:

No comments

Related manuals for ValueJet VJ-1627MH

Pixma MG2400 Series

Brand: Canon Pages: 2

ImageCLASS MF4570dw

Brand: Canon Pages: 164

imagePRESS C800 Series

Brand: Canon Pages: 132

ImageCLASS MF5730

Brand: Canon Pages: 2

Brand: NCR Pages: 36

Brand: NCR Pages: 206

Brand: NCR Pages: 138

Brand: LabelTac Pages: 2

Brand: EasyThreed Pages: 4

Brand: EASYPRINT Pages: 37

Brand: Kodak Pages: 2

Brand: QMS Pages: 180

Brand: Sindoh Pages: 33

Brand: SAGEMCOM Pages: 146

SignJet JS310 Series

Brand: GRAPHTEC Pages: 83

Accel-a-Writer 8200

Brand: Xante Pages: 12

KYOCERA FS-C8100DN

Brand: Kyocera Pages: 12

Brand: Tally Pages: 174

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands