Muton ValueJet VJ-1627MH Startup Manual Download Page 8

Page: 8 / 56

Assembling

Follow the procedure below to assemble the stand.

Assemble the printer

Four or more people are required to assemble this printer.

Procedure for assembling the stand

[1]

Assemble the right stand.

[2]

Attach the right leg part to the right base part so that four screw holes

in the base part are at the front.

[3]

Tighten two hexagon socket head cap screws using a hexagonal wrench (supplied accessory).

[4]

Assemble the left stand in the same way as in Step 2, 3.

[5]

Fasten the connector bar to the right stand using two hexagon socket

head cap screws.

• Attach the connector bar with the groove facing the rear as shown

left.

Assembling

CAUTION

Leg (right)

Base

Hexagon socket head cap
screws

Screw holes

Front

Screw holes

Front

Leg (left)

Base

Hexagon socket head cap
screws

Stand (right)

Connector bar

Hexagon socket
head cap screws

the groove surface

Front

Summary of Contents for ValueJet VJ-1627MH

























































Search results

Summary of Contents for ValueJet VJ-1627MH

Reviews:

Related manuals for ValueJet VJ-1627MH

Brands by name

Popular brands

Muton ValueJet VJ-1627MH, Startup Manual

Search results

Summary of Contents for ValueJet VJ-1627MH

Reviews:

Related manuals for ValueJet VJ-1627MH

Brands by name

Popular brands