Murr Elektronik Data Panel xtreme DB DP-34044-1, User Manual

Page: 30 / 54

30
Value
83 (0x53)
Name Data Type Byte Bits Description
Command Byte 1 Command for index pointer (which message you’re sending)
OUTMODE1A
4 bit
2
1,2,3,4
Mode 0x0=disabled, 0x1=On/Off, 0x2=Data(0-4000), 0x3=Percent(0-1000 = 0-100.0%),
0x4=Amps(0-4000 = 0-4.000A)
OUTMODE1B 5,6,7,8
OUTMODE2A
3
1,2,3,4
OUTMODE2B 5,6,7,8
OUTMODE3A
4
1,2,3,4
OUTMODE3B 5,6,7,8
OUTMODE4A
5
1,2,3,4
OUTMODE4B 5,6,7,8
INMODE5A
6
1,2,3,4 Mode 0x0=disabled, 0x1=Digital Positive, 0x2=Digital Ground
INMODE5B 5,6,7,8
Mode 0x0=disabled, 0x1=Digital Positive, 0x2=Digital Ground, 0x3= 4-20mA (4000-20000),
0x4= 0-5V DC (0-5000, 0x5= 0-10V DC (0-10000), 0x6= 0-32V DC(0-32000),
0x9= Ratiometric (0-100.0% of source V DC)
INMODE6A
7
1,2,3,4 Mode 0x0=disabled, 0x1=Digital Positive, 0x2=Digital Ground
INMODE6B 5,6,7,8
Mode 0x0=disabled, 0x1=Digital Positive, 0x2=Digital Ground, 0x3= 4-20mA (4000-20000),
0x4= 0-5V DC (0-5000, 0x5= 0-10V DC (0-10000), 0x6= 0-32V DC(0-32000),
0x9= Ratiometric (0-100.0% of source V DC)
INMODE7A 4 bit 8 1,2,3,4
Mode 0x0=disabled, 0x1=Digital Positive, 0x2=Digital Ground, 0x7=Digital Positive Frequency ,
0x8= Counter, 0xA=Encoder
INMODE7B 4 bit 8 5,6,7,8
Mode 0x0=disabled, 0x1=Digital Positive, 0x2=Digital Ground, 0x3= 4-20mA (4000-20000),
0x4= 0-5V DC (0-5000, 0x5= 0-10V DC (0-10000), 0x6= 0-32V DC(0-32000),
0x9= Ratiometric (0-100.0% of source V DC)
5.3.6 FREUENCY
A. The input must be put into Frequency MODE = 7 (Only valid on input 7A & 8A)
This puts the Input into frequency operation mode. When a positive signal is present on the input pin, the frequency will be shown.
Value
84 (0x54)
Name Data Type Byte Bits Description
Command Byte 1 Command for index pointer (which message your sending)
INMODE8A 4 bit 2 1,2,3,4
Mode 0x0=disabled, 0x1=Digital Positive, 0x2=Digital Ground, 0x7=Digital Positive Frequency ,
0x8= Counter
INMODE8B 4 bit 2 5,6,7,8
Mode 0x0=disabled, 0x1=Digital Positive, 0x2=Digital Ground, 0x3= 4-20ma (4000-20000),
0x4= 0-5V DC (0-5000, 0x5= 0-10V DC (0-10000), 0x6= 0-32V DC (0-32000),
0x9= Ratiometric (0-100.0% of source V DC)
Port 1A Kp
Byte
3 Output 1A proportional set point (0-250 = 0-2.50, >250=0) default 100
Port 1A Ki 4 Output 1A integral set point (0-250 = 0-2.50, >250=0) default 100
Port 1B Kp 5 Output 1B proportional set point (0-250 = 0-2.50, >250=0) default 100
Port 1B Ki 6 Output 1B integral set point (0-250 = 0-2.50, >250=0) default 100
Port 2A Kp 7 Output 2A proportional set point (0-250 = 0-2.50, >250=0) default 100
Port 2A Ki 8 Output 2A integral set point (0-250 = 0-2.50, >250=0) default 100