background image

READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.

This instruction manual complies with the Treestand Manufacturers Association’s TMS 04 -

 Standard Practice for Treestand Instructions

 and TMS 02 - 

Standard Test Method for Treestand Fall Arrest Systems.

attEntIon!! 

WHEn You sEE a “  WarnInG!” BE surE to HEED tHE MEssaGE! 

tHE InForMatIon contaInED In tHEsE MEssaGEs can saVE Your lIFE!!

7

E

Sleeved Rail

Supports

E

E

E

Sleeved Rail

Supports

Shooting Rail

Connector

Shooting Rail

Shooting Rail

Connector

Shooting Rail

stEP 5.

 Assemble the 

shooting rail

 by inserting the 

shooting 

rail connectors

 into the 

shooting rails

 and aligning holes.  

Connect the 

shooting rail

 to the inside of the 

sleeved rail 

supports

 using (4) 5/16” x 2 1/4” hex bolts [E], (8) nylon washers 

and (4) 5/16” nylock nuts (Fig. 5). 

stEP 6.

 Attach the 

rail supports

 to the outer edge of the 

foot platform

 

and 

shooting rail

 using center holes, secure using (4) 5/16” x 2 1/4” hex 

bolts [E], (8) nylon washers and (4) 5/16” nylock nuts (Fig. 6).  

E

E

E

Shooting Rail

Foot Platform

Rail

Support

E

Rail

Support

FIG. 5

FIG. 6

D

Foot Platform

Cross braces

D

Rail

Support

D

Cross braces

Rail

Support

D

D

D

FIG. 7

Roof

Supports

Roof

Supports

Rail

Supports

Delta bolt

Delta bolt

Delta bolt

Delta bolt

Rail

Supports

FIG. 8

stEP 7. 

Then connect (4) 

rail support braces

 to the 

rail supports

 

and the 

foot platform

 using (6) 5/16” x 1 3/4” hex bolts [D], (12) 

nylon washers and (6) 5/16” nylock nuts. 

notE:

 The 

cross braces

 

are attached to the outside of the 

foot platforms

 and to the inside 

of the 

rail supports

 (Fig. 7).

stEP 8.

 Insert the 

roof supports

 into the 

welded sleeves on the 

rail supports

 and 

secure using (4) 5/16” delta bolts from the 

inside. 

notE:

 

The bends 

on the 

roof 

supports

 shall 

be to the top 

and pointing to 

the center of the 

foot platform

 

(Fig. 8).

 WARNING! A shooting rail has been provided for support/and or 

comfort and is not designed to carry the full weight of the user. Never 

place more than 15 lbs (7 kg) on these structures. Failure to follow these 

instructions may result in serious injury or death!

Summary of Contents for The Renegade MQP1500













Reviews: