MTU 12 V 2000 P12 Operating Instructions Manual Download Page 70

Page: 70 / 187

Fault code

Fault message

Meaning

Action

216

SD T-LUBE OIL

Sensor B07 faulty (lube oil

temperature).

1. Check cabling (→ Engine oper‐

ating instructions);

2. Contact Service

• Check sensor.

219

SD T-INTAKE AIR

Sensor B03 faulty (intake

air temperature).

1. Check cabling (→ Engine oper‐

ating instructions);

2. Contact Service

• Check sensor.

220

SD COOLANT LEV‐

Sensor F33 faulty (engine

coolant level 1).

1. Switch system off and back on;

2. check fault message;

3. check cabling (→ Engine oper‐

ating instructions);

4. Contact Service

• Check sensor.

222

SD LEVEL LEAK‐

AGE FUEL

Sensor fault (leak fuel).

1. Check cabling (→ Engine oper‐

ating instructions);

2. Contact Service

• Check sensor.

223

SD LEVEL INTER‐

COOLER

Sensor fault (charge air

coolant level).

1. Check cabling (→ Engine oper‐

ating instructions);

2. Contact Service

• Check sensor.

229

SD ENG. SPEED

SENSORS

Sensor fault crankshaft

speed and camshaft

speed.

1. Check cabling (→ Engine oper‐

ating instructions);

2. Contact Service

• Check sensor.

230

SD CRANKSHAFT

SPEED

Sensor B13 faulty (crank‐

shaft speed).

1. Check cabling (→ Engine oper‐

ating instructions);

2. Contact Service

• Check sensor.

231

SD CAMSHAFT

SPEED

Sensor B1 faulty (camshaft

speed).

1. Check cabling (→ Engine oper‐

ating instructions);

2. Contact Service

• Check sensor.

232

SD CHARGER

SPEED 1

Sensor B44 faulty (ETC

speed 1).

1. Check cabling (→ Engine oper‐

ating instructions);

2. Contact Service

• Check sensor.

240

SD P-FUEL

Sensor B34 faulty (fuel

pressure).

1. Check cabling (→ Engine oper‐

ating instructions);

2. Contact Service

• Check sensor.

245

SD POWER SUP‐

PLY

Sensor fault (ECU operat‐

ing voltage).

Replace engine governor (→ En‐

gine operating instructions).

246

SD T-ELECTRONIC Temperature sensor for

measuring electronics tem‐

perature faulty.

Replace engine governor (→ En‐

gine operating instructions).

250

SD CAN SPEED DE‐

MAND

Sensor fault (CAN setpoint

speed).

Contact Service.

• Check CAN communication.

266

SD SPEED DE‐

MAND AN.

External speed setting faul‐

ty.

(→ Engine operating instructions)

1. Check cabling

2. Check speed setting.

70 | Troubleshooting | MS150025/02E 2012-10

TIM-ID: 0000008959 - 001

Summary of Contents for 12 V 2000 P12




























































































































































































Search results

Summary of Contents for 12 V 2000 P12

Reviews:

Related manuals for 12 V 2000 P12

Brands by name

Popular brands

MTU 12 V 2000 P12, Operating Instructions Manual

Search results

Summary of Contents for 12 V 2000 P12

Reviews:

Related manuals for 12 V 2000 P12

Brands by name

Popular brands