MTU 12 V 2000 P12 Operating Instructions Manual Download Page 143

Page: 143 / 187

7.18 Engine Mounting / Support

7.18.1 Engine mounts – Resilient elements check

Preconditions

☑ Engine is stopped and starting disabled.
☑ Engine is filled with coolant and engine oil.

Engine mounts – Resilient

elements check

Wipe rubber surface with dry cloth, do not

use organic detergents.

Check resilient elements for crack formation

and deformation by visual inspection.

Have cracked elements replaced, contact

Service.

Setting dimension check

Measure setting dimension:

• Dimension (a) = 55 mm.

If dimension (a) is less than 55 mm, resilient elements must be replaced. Contact Service.

MS150025/02E 2012-10 | Task Description | 143

TIM-ID: 0000007552 - 001

Summary of Contents for 12 V 2000 P12




























































































































































































Search results

Summary of Contents for 12 V 2000 P12

Reviews:

Related manuals for 12 V 2000 P12

Brands by name

Popular brands

MTU 12 V 2000 P12, Operating Instructions Manual

Search results

Summary of Contents for 12 V 2000 P12

Reviews:

Related manuals for 12 V 2000 P12

Brands by name

Popular brands