MTHTrains Premier SD50 Diesel Engine Operator'S Manual Download | Manualshive

Page: 18 / 47

background image

Additional F Functions

F14-F16 – Idle Sequence

Pressing F14, F15, or F16 twice (toggling on then off) will trigger an Idle Sequence if
the engine is not moving. These vary from engine to engine and may include things like
checking the coal load, checking the water level, using the Alemite grease gun on the
drivers, etc. When triggered, these will run through the sequence that varies in duration.

NOTE: The engine must be sitting still in order to trigger these

F17 – Extended Start-Up

If your engine is shut down or you've just applied DCC power pressing F17 twice
(toggling it on then off) will start the Extended Start-Up
sounds. This is very similar to F3 except you will hear the crew talking back and forth
about getting the engine ready to run.

F18 – Extended Shut-Down

If your engine is already up and running you can play the Extended Shut Down sounds
by pressing F18 twice (toggling on then off). The Extended Shut Down is very similar
to F3 in that the engine will ultimately shut down, but in the case of Extended Shut
Down you will hear the crew talking back and forth about how the engine ran, time
schedules, etc.

F19 – Rev Up

Pressing F19 twice will increase the diesel engine's rev level by one notch. Two more
presses of F19 will rev the diesel engine to the second notch and so forth. You can rev
the engine up 7 notches from idle. This is useful if you wish to simulate a heavy load
behind the train and want to rev the diesel engine up.

F20 – Rev Down

Pressing F20 twice will decrease the diesel engine's rev level by one notch. Two more
presses of F20 will rev the diesel engine down one more notch and so forth. You can
rev the engine down to its idle rev level as long as it's sitting still.

F21 – One Shot Doppler

You can set your MTH PS3.0-equipped engine to simulate the actual Doppler Effect
sound a real engine makes as it passes you. To do this, press the F21 button once
(enable F21) and then listen as the engine makes that pitch shift that mimics the
Doppler Effect perfectly. Press the F21 button again (disable F21) to shut off the
Doppler Effect. With a little practice in timing and speed you can make this happen
right in front of you.

F22 – Coupler Slack

When an engine hooks up and pulls a train it has to take up the coupler slack. You can
play this sound by pressing F22 twice (toggling on then off). This feature works two
ways – While the engine is sitting still, press F22 twice to enable it. Then, when you
move the engine, it will play the Coupler Slack sound.

The second way is to simply force the sound while the engine is moving. To do this,
simply press F22 twice (toggling it on then off). The sound will play.

Premier SD50 Diesel Engine

18

«
...
16
17
18
19
20
...
»

Summary of Contents for Premier SD50 Diesel Engine
















































Reviews:

No comments

Related manuals for Premier SD50 Diesel Engine

Brand: Gayla Pages: 2

Brand: LaTrax Pages: 12

MARINER 40 MK II ARF

Brand: Lanier R/C Pages: 14

Brand: marklin Pages: 44

Learn & Groove Shakin Colors Maracas

Brand: LeapFrog Pages: 12

Brand: Blade Pages: 17

Brand: Barbie Pages: 12

Brand: Faller Pages: 16

Brand: Magformers Pages: 24

Brand: Horizon Hobby Pages: 18

Brand: Horejsi Pages: 5

Brand: Radio Shack Pages: 16

Brand: Trix Pages: 76

N-Strike Mega Bulldog

Brand: Nerf Pages: 2

Baby GymTasTics Zebra K0317

Brand: Fisher-Price Pages: 6

Brand: Pilot Communications Pages: 37

1563W Wabash Freight Set

Brand: Lionel Pages: 24

BABY born Sister Styling Creative Head

Brand: Zapf Creation Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands