MTHTrains Premier SD50 Diesel Engine Operator'S Manual Download | Manualshive

Page: 10 / 47

background image

Passenger/Freight Announcements (PFA)

Your engine is equipped with a sound package of either passenger station
announcements or freight yard sounds that you can play when you pull into a station or
a yard. Each sequence described below will play as long as it is left on, randomly
generating sounds, but be sure to allow approximately 30 seconds between the button
pushes described below to allow the PFA sufficient time to run through each sequence.

To cue the sound system to play the PFA, quickly but firmly tap the Bell

button once followed by 2 quick taps of the Horn button while the engine is
moving. Tap the buttons quickly but allow approximately ½ second between
each press.

Press the Direction button once to stop the engine. This will trigger the first

sequence of PFA. The reverse unit is temporarily disabled so that the train will
not move as you use the Direction button to trigger the sounds. Proto-Sound
3.0 has disabled operator control over the Horn and Bell buttons until the full
PFA sequence is complete.

After waiting about 30 seconds for that sequence to run, press the Direction

button again to trigger the second sequence of PFA.

After about 30 seconds, press the Direction button again to trigger the third

PFA sequence.

Again, after allowing about 30 seconds for that sequence to run, press the

Direction button one more time to trigger the fourth and final PFA sequence.
The PFA will continue and within a few seconds the bell will begin ringing,
then the engine will begin moving at the current throttle setting, in the same
direction it was traveling when you began the sequence. Once the bell turns
off, the operator regains control of the transformer's bell and Horn buttons
and can ring the bell or blow the Horn as usual.

•

•

•

•

•

Premier SD50 Diesel Engine

10

«
...
8
9
10
11
12
...
»

Summary of Contents for Premier SD50 Diesel Engine
















































Reviews:

No comments

Related manuals for Premier SD50 Diesel Engine

Brand: WattAge Pages: 32

Brand: PLAYTIVE JUNIOR Pages: 20

minideices 17865

Brand: Lansay Pages: 2

Build-a-ma-Jigs Racetruck BX1221

Brand: B Pages: 2

Brand: HOBBY ENGINE Pages: 8

MINI SKY HUNTER

Brand: H-KING Pages: 8

Brand: PARKZONE Pages: 12

Lightning Flash Roller Coaster

Brand: K'Nex Pages: 23

Brand: Tekno Pages: 28

SBD-5 Dauntless engine

Brand: Eduard Pages: 2

Havoc Turbo Blast

Brand: Air Hogs Pages: 4

Chocolate Sprinkle Stix

Brand: John Adams Pages: 2

6-8-6 Steam Turbine Engine

Brand: Rail King Pages: 32

AXN Floater Jet

Brand: H-KING Pages: 18

Call of Duty DPW84

Brand: Mega Construx Pages: 24

Brand: Vollmer Pages: 3

GWR TOAD Diagram AA7

Brand: Connoisseur Models Pages: 14

Imagine-Build-Play SWING RIDE

Brand: K'Nex Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands