MTHTrains Premier SD50 Diesel Engine Operator'S Manual Download | Manualshive

Page: 35 / 47

background image

Traction Tire Replacement Instructions

Your locomotive is equipped with two neoprene rubber traction tires on each powered
truck block. While these tires are extremely durable, they may occasionally need
replacement.

First, remove the truck sides from the truck block by unscrewing the mounting screws
as noted in Figure 9.

Once the truck sides have been removed:

1. Make sure the old tire has been completely removed from the groove in the drive
wheel, using a razor blade or small flathead screwdriver to pry away any remains.

2. Slip the new tire onto the wheel. You may find it useful to use two small flathead
screwdrivers to stretch the tire over the wheel.

3. If you twist the tire while stretching it over the wheel, you will need to remove and
reinstall the tire. Otherwise your engine will wobble while operating.

4. Make sure the tire is fully seated inside the groove. Use a razor blade to trim away any
excess tire that will not seat inside the groove properly.

5. Reassemble in the reverse order.

Headlight Replacement Instructions

The PS 3.0 headlights and other associated lights are small LEDs that require a lot less
power and generate a lot less heat than incandescent bulbs, resulting in extremely long
life compared to the incandescent bulbs. The LEDs are not user serviceable.

Premier SD50 Diesel Engine

35

Figure 11: Truck Side Screws

Truck Side Screws

«
...
33
34
35
36
37
...
»

Summary of Contents for Premier SD50 Diesel Engine
















































Reviews:

No comments

Related manuals for Premier SD50 Diesel Engine

Brand: AeroWorks Pages: 17

SQUADRON'S STEARMAN

Brand: RED BARON PIZZA Pages: 39

Spirit GPMA0530

Brand: GREAT PLANES Pages: 40

Maker ROK Robotics

Brand: Rokenbok Pages: 4

ACCUCRAFT 7/8 SCALE 7 x 12 INCH BAGNALL

Brand: Accucraft Pages: 8

Brand: Fisher-Price Pages: 6

Little Home 460498

Brand: Jamara Pages: 4

Happy Cruisers BX1781Z

Brand: B.toys Pages: 2

Brainy Baby Number Bug

Brand: VTech Pages: 9

B&O 0-4-0 DOCKSIDE

Brand: AML Pages: 8

Extra 300 PNP/BNF

Brand: PARKZONE Pages: 88

ROCKY IGED0092US

Brand: Peg-Perego Pages: 24

PREMIER E8 ABA DIESEL ENGINE

Brand: M.T.H. Pages: 24

Monkey Chase H8128

Brand: Fisher-Price Pages: 4

Radio Control Pterodactyl

Brand: Toysrus Pages: 2

Brand: Fisher-Price Pages: 4

Imagine Build Play MULTI-MOTOR 13074

Brand: K'Nex Pages: 72

Brand: Fisher-Price Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands