MTHTrains Premier SD50 Diesel Engine Operator'S Manual Download | Manualshive

Page: 36 / 47

background image

Starting Up

Horn

Bell

Solution

Solution

Solution

Only my headlight comes on, nothing
else.

When I first turn the power on, the
engine will not begin to run.

The engine will not start after I press the
Direction button.

I can't get the horn to blow when I press
the Horn button.

I can't get the bell to ring when I press
the bell button.

You may be pressing the button too quickly.
Try pressing the Horn button more slowly,
taking approximately one full second to fully
depress the button.

You may be pressing the button too quickly.
Try pressing the bell button more slowly,
taking approximately one full second to fully
depress the button.

This is normal behavior. The super capacitors
are charging and this will take between 1-20
seconds.

This is normal behavior. To prevent accidental

®

high-speed start-ups, Proto-Sound 3.0 is
programmed to start up in neutral anytime
track power has been turned off for several
seconds. See the “Basic Operation” section for
more details.

You may not be sending enough power to the
track to power the engine. Rotate throttle
clockwise to increase track power.

Coupler

Solution

When I try to fire the coupler, PFA starts.

The Proto-Coupler™ won't let the engine
uncouple on the fly.

The coupler does not fire or stay coupled.

You are waiting too long between Horn button
presses. See the timing instructions located at
the beginning of the "Proto-Sound® 3.0
Operating Instructions" section.

Try lubricating the coupler knuckle and rivet
with a dry graphite lubricant.

The coupler needs to be cleaned. Wipe with
denatured alcohol (not rubbing alcohol) and
let dry.

Cab Chatter

Solution

Sometimes the Cab Chatter sounds
don't play.

Cab Chatter plays only in neutral at random
intervals.

Although Proto-Sound® 3.0 has been designed and engineered for ease of use, you may
have some questions during initial operation. The following table should answer most
questions. If your problem cannot be resolved with this table, contact M.T.H. for
assistance (telephone: 410-381-2580; fax: 410-423-0009; [email protected],
7020 Columbia Gateway Drive, Columbia MD 21046-1532).

Troubleshooting Proto-Sound® 3.0 Problems

Conventional AC

Premier SD50 Diesel Engine

36

«
...
34
35
36
37
38
...
»

Summary of Contents for Premier SD50 Diesel Engine
















































Reviews:

No comments

Related manuals for Premier SD50 Diesel Engine

Brand: Bell Pages: 220

THE GHOST HOUSE

Brand: RavensBlight Pages: 10

Bf 109E-4 interior S.A.

Brand: Eduard Pages: 4

Brand: Faller Pages: 8

F-16C FIGHTING FALCON 1120mm 28/2021

Brand: Paper Replika Pages: 3

Mini Cooper 0582

Brand: National Products Pages: 24

Orc Krushinator Deffstomper Body

Brand: Tabletop Scenics Pages: 20

Brand: WATT AGE Pages: 32

Brand: Ultrafly Pages: 11

Brand: H-KING Pages: 41

Brand: Walkera Pages: 22

Electronic flash magic

Brand: LeapFrog Pages: 4

Brand: Funkey Pages: 6

Brand: Multiplex Pages: 32

He 111 H-6 bomb bay

Brand: Eduard Pages: 3

Brand: VTech Pages: 12

AJO THUNDERBOLT

Brand: J-Power Pages: 31

Brand: Smoby Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands