background image

MTH Tool Company, Inc. / MTH Pumps,
hereinafter referred to as “MTH”, war-
rants for a period of twelve (12) months
from the date of shipment (“The War-
ranty Period”), that the pumps
manufactured by it will be free from
defects in material and workmanship.
MTH will correct defects in material or
workmanship which may develop in its
products under proper or normal use
during the Warranty Period and under
the conditions of this Warranty.  This
Warranty does not extend to anyone
except the original consumer-purchas-
er.  Damage to the product due to
improper handling, improper storage,
improper maintenance, or improper ap-
plication is not covered by this
Warranty.  Warranty claims for motors,
mechanical seals, and accessories
should be directed to those who manu-
factured the component.  MTH will
repair or replace, at its option and ex-
pense, its products proved to be

defective after examination by the Com-
pany.  The defective Product must be
returned, transportation prepaid, to the
factory at Plano, Illinois.  Disassembly
of the equipment impairs determination
of reasons for failure and shall be cause
for voiding this Warranty.  The Product,
repaired or replaced, will be shipped
f.o.b. MTH’s factory.  This is MTH's
sole warranty.    MTH makes no other
warranty of any kind, expressed or
implied, and all implied warranties of
merchantability and fitness for a par-
ticular purpose which exceed MTH's
aforestated obligations are hereby
disclaimed by MTH and excluded
from this warranty. 
 MTH neither as-
sumes nor authorizes any person to
assume for it, any other obligation in
connection with the sale of the Product
and any enlargement of this Warranty
by a purchaser shall be for its own
account and its exclusive responsibility.
This Warranty shall not apply to any

7.

Limited Warranty

Product or parts of Products which:  (a)
have been repaired or altered outside of
MTH’s factory, in any manner; or (b)
have been subjected to misuse, negli-
gence or accident; or (c) have been
used in a manner contrary to MTH’s
printed instructions; or (d) have been
damaged due to defective power supply
or faulty installation.    MTH shall not be
liable for incidental and consequen-
tial losses and damages under this
express warranty, any applicable im-
plied warranty, or claims for
negligence, except to the extent that
this limitation is found to be unen-
forceable under the applicable State
law.  Some States do not allow the
exclusion or limitation of incidental
or consequential damages, so the
above limitation or exclusion may
not apply to you.  This warranty gives
you specific legal rights, and you
may also have other rights which
vary from State to State.

6A Parts

Repair parts may be obtained
through your local Authorized MTH
Pumps Representative or Distribu-
tor who can be found in the yellow
pages or by contacting MTH Pumps
at 401 W. Main St. • Plano, IL
60545  Phone: 630-552-4115
Fax: 630-552-3688.

6B Repair Services

Repair service for an MTH pump
should be obtained from the
company through which it was
purchased.

6.

A. Parts
B. Repair Service
C. Warranty Service
D. Motors, Mechanical Seals,

and Accessories

In the event this is not possible, the
name and phone number of a
nearby MTH representative or
distributor may be obtained by
contacting MTH Pumps.  In the
event that it is necessary to return
the pump to the factory for repairs,
remove all accessories attached to
the pump.  We cannot accept
responsibility for their safe removal,
storage, and return.

6C Warranty Service

All requests for warranty claims
should be made through the
company from which the pump was
purchased or supplied.  Complete
details on what is wrong with the
pump must be provided along with
information on the system in which
it is installed.  Refer to the MTH
Pumps Limited Warranty statement.

Return authorization must be
obtained prior to returning any
equipment.

6D Motors, Mechanical Seals,
and Accessories

Repair or replacement service on
motors, mechanical seals, relief
valves, or other accessories should
be obtained from the manufacturer
of these components. MTH does
not carry replacement parts and is
not authorized to render repair
service on these components.
Replacement mechanical seals are
stocked at MTH and are always
available insofar as possible for
immediate shipment.  Warranty
service, as well as expert applica-
tion information can be obtained
from your local seal manufacturer's
sales office.

Parts and Repair Services

T51 SERIES

T51 SERIES

MTH PUMPS

401 West Main Street  •  Plano, IL  60545-1436

Phone:  630-552-4115   •   Fax:  630-552-3688

Page 520

Dated January 2000

97-4623-01-588

Summary of Contents for T51 SERIES





















Reviews: