MR VACUTAP VV Installation And Commissioning Instructions Download Page 174

Page: 174 / 198

7 Fault elimination

Maschinenfabrik Reinhausen GmbH 2020

174

4349322/01 EN

VACUTAP

2. Contact and inform Maschinenfabrik Reinhausen of the following:

What was the load of the transformer at the instant of tripping?

Was there a tap-change operation on the on-load tap-changer immedi-
ately before or during the tripping?

Did any other protective devices of the transformer respond at the in-
stant of tripping?

Were switching operations in the network being carried out at the in-
stant of tripping?

Were overvoltages registered at the instant of tripping?

How high is the static pressure on the pressure relief device (height dif-
ference between the oil level in the on-load tap-changer oil conservator
and the pressure relief device)?

3. Take further action in agreement with Maschinenfabrik Reinhausen.

7.2.3 Re-commissioning the transformer

You can re-commission the transformer once the cause for tripping the pres-
sure monitoring device has been determined and resolved:

1. Ensure that the sensor on the snap-action switch is in the OPERATION

position.

2. Commission the transformer.

Summary of Contents for VACUTAP VV







































































































































































































Search results

Summary of Contents for VACUTAP VV

Reviews:

Related manuals for VACUTAP VV

Brands by name

Popular brands

MR VACUTAP VV, Installation And Commissioning Instructions

Search results

Summary of Contents for VACUTAP VV

Reviews:

Related manuals for VACUTAP VV

Brands by name

Popular brands