MR VACUTAP VV Installation And Commissioning Instructions Download Page 66

Page: 66 / 198

5 Mounting

Maschinenfabrik Reinhausen GmbH 2020

4349322/01 EN

VACUTAP

5.3.5.2.1 Moving on-load tap-changer to adjustment position

► Move the on-load tap-changer to the adjustment position. The adjustment

position is indicated in the on-load tap-changer connection diagram in-
cluded in delivery.

5.3.5.2.2 Removing on-load tap-changer head cover

WARNING

Danger of explosion!

Explosive gases under the on-load tap-changer head cover can deflagrate
or explode and result in severe injury or death.

► Ensure that there are no ignition sources such as open flames, hot sur-

faces or sparks (e.g. caused by the build-up of static charge) in the imme-
diate surroundings and that none occur.

► De-energize all auxiliary circuits (for example tap-change supervisory de-

vice, pressure relief device, pressure monitoring device) before removing
the on-load tap-changer head cover.

► Do not operate any electrical devices during the work (e.g. risk of sparks

from impact wrench).

NOTICE

Damage to the on-load tap-changer!

Small parts in the oil compartment may block the diverter switch insert,
thereby damaging the on-load tap-changer.

► Ensure that parts do not fall into the oil compartment.

► Check that all small parts are accounted for.

1. Ensure that the inspection window is sealed off with the cover.

2. Remove the screws and washers from the on-load tap-changer head

cover.

Figure 47: On-load tap-changer head cover

Summary of Contents for VACUTAP VV







































































































































































































Search results

Summary of Contents for VACUTAP VV

Reviews:

Related manuals for VACUTAP VV

Brands by name

Popular brands

MR VACUTAP VV, Installation And Commissioning Instructions

Search results

Summary of Contents for VACUTAP VV

Reviews:

Related manuals for VACUTAP VV

Brands by name

Popular brands