MR VACUTAP VV Installation And Commissioning Instructions Download Page 49

Page: 49 / 198

5 Mounting

Maschinenfabrik Reinhausen GmbH 2020

4349322/01 EN

VACUTAP

3. Remove on-load tap-changer head cover.

Figure 31: On-load tap-changer head cover

5.2.5.1.3 Drying the on-load tap-changer

NOTICE

Damage to the on-load tap-changer head cover and on-load tap-
changer accessories.

Both the on-load tap-changer head cover and the on-load tap-changer ac-
cessories will become damaged if they are dried.

► Never dry the on-load tap-changer head cover or the following acces-

sories: motor-drive unit, drive shaft, protective relay, pressure monitoring
device, pressure relief device, bevel gear, temperature sensor, oil filter
unit.

1. Heat up the on-load tap-changer in air at atmospheric pressure with a

temperature increase of approximately 10 °C/h to a final temperature of
maximum 110 °C.

2. Pre-dry the on-load tap-changer in circulating air at a maximum tempera-

ture of 110 °C for a period of at least 20 hours.

3. Vacuum-dry on-load tap-changer at between 105 °C and maximum

125 °C for at least 50 hours.

4. Residual pressure of no more than 10

-3

bar.

Summary of Contents for VACUTAP VV







































































































































































































Search results

Summary of Contents for VACUTAP VV

Reviews:

Related manuals for VACUTAP VV

Brands by name

Popular brands

MR VACUTAP VV, Installation And Commissioning Instructions

Search results

Summary of Contents for VACUTAP VV

Reviews:

Related manuals for VACUTAP VV

Brands by name

Popular brands