Moxa Technologies EDS-505A Series User Manual Download Page 99

Page: 99 / 129

EDS-508A/505A Series User’s Manual

Featured Functions

3-84

LLDP Settings

Enable LLDP

Setting

Description

Factory Default

Enable or Disable Enable or disable LLDP function.

Enable

Value

Setting

Description

Factory Default

Numbers from
5~32768 secs

To set the transmit interval of LLDP messages. Unit is
in seconds.

30 (seconds)

LLDT Table

Port

Neighbor ID

Neighbor Port

Description

Neighbor System

Port:

The port number that connects to the neighbor device.

Neighbor ID:

A unique entity which identifies a neighbor device; this is typically the MAC

address.

Neighbor Port:

The port number of the neighbor device.

Neighbor Port Description:

A textual description of the neighbor device’s interface.

Neighbor System:

Hostname of the neighbor device.

Summary of Contents for EDS-505A Series


































































































































Search results

Summary of Contents for EDS-505A Series

Reviews:

Related manuals for EDS-505A Series

Brands by name

Popular brands

Moxa Technologies EDS-505A Series, User Manual

Search results

Summary of Contents for EDS-505A Series

Reviews:

Related manuals for EDS-505A Series

Brands by name

Popular brands