Moxa Technologies EDS-505A Series User Manual Download Page 102

Page: 102 / 129

EDS-508A/505A Series User’s Manual

Featured Functions

3-87

The table will display the following information:

MAC

This field shows the MAC address

Type

This field shows the type of this MAC address

Port

This field shows the port that this MAC address belongs to

Using Event Log

Bootup

This field shows how many times the EDS has been rebooted or cold started.

Date

The date is updated based on how the current date is set in the “Basic Setting” page.

Time

The time is updated based on how the current time is set in the “Basic Setting” page.

System
Startup
Time

The system startup time related to this event.

Events

Events that have occurred.

NOTE

The following events will be recorded into the EDS’s Event Log table:
1.

Cold start

Warm start

Configuration change activated

Power 1/2 transition (Off



On), Power 1/2 transition (On



Off)

Authentication fail

Topology changed

Master setting is mismatched

DI 1/2 transition (Off



On), DI 1/2 transition (On



Off)

Port traffic overload

10.

dot1x Auth Fail

11.

Port link off / on

Summary of Contents for EDS-505A Series


































































































































Search results

Summary of Contents for EDS-505A Series

Reviews:

Related manuals for EDS-505A Series

Brands by name

Popular brands

Moxa Technologies EDS-505A Series, User Manual

Search results

Summary of Contents for EDS-505A Series

Reviews:

Related manuals for EDS-505A Series

Brands by name

Popular brands