Moxa Technologies EDS-505A Series User Manual Download Page 81

Page: 81 / 129

EDS-508A/505A Series User’s Manual

Featured Functions

3-66

Configuring GMRP

GMRP is a MAC-based multicast management protocol, whereas IGMP is IP-based. GMRP
provides a mechanism that allows bridges and end stations to register or un-register Group
membership information dynamically.

GMRP enable

Setting

Description

Factory Default

Enable/Disable

Select the option to enable the GMRP function for the
port listed in the Port column

Disable

GMRP Table

The EDS displays the current active GMRP groups that were detected.

Setting

Description

Fixed Ports

This multicast address is defined by static multicast.

Learned Ports

This multicast address is learned by GMRP.

Summary of Contents for EDS-505A Series


































































































































Search results

Summary of Contents for EDS-505A Series

Reviews:

Related manuals for EDS-505A Series

Brands by name

Popular brands

Moxa Technologies EDS-505A Series, User Manual

Search results

Summary of Contents for EDS-505A Series

Reviews:

Related manuals for EDS-505A Series

Brands by name

Popular brands