Moxa Technologies EDS-505A Series User Manual Download Page 54

Page: 54 / 129

EDS-508A/505A Series User’s Manual

Featured Functions

3-39

Shows which communication protocol is in use:

Turbo Ring

Turbo Ring V2

RSTP

Turbo

Chain

None

The “Ports Status” indicators show

Forwarding

for normal transmission,

Blocked

if this port is

connected to the Tail port as a backup path and the path is blocked, and

Link down

if there is no

connection.

Explanation of “Settings” Items

Redundancy Protocol

Setting

Description

Factory Default

Turbo Ring

Select this item to change to the Turbo
Ring configuration page.

Turbo Ring V2

Select this item to change to the Turbo
Ring V2 configuration page.

Turbo Chain

Select this item to change to the Turbo
Chain configuration page

RSTP (IEEE
802.1W/1D)

Select this item to change to the RSTP
configuration page.

None

Ring redundancy is not active

None

Role

Setting

Description

Factory Default

Head

Select this EDS as Head Switch

Member

Select this EDS as Member Switch

Tail

Select this EDS as Tail Switch

Member

Head Role

Setting

Description

Factory Default

Head Port

Select any port of the EDS to be the head
port.

EDS-505A: port 4
EDS-508A: port 7

Member Port

Select any port of the EDS to be the
member port.

EDS-505A: port 5
EDS-508A: port 8

Member Role

Setting

Description

Factory Default

Member port

Select any port of the EDS to be the 1

member port

EDS-505A: port 4
EDS-508A: port 7

Member port

Select any port of the EDS to be the 2

member port

EDS-505A: port 5
EDS-508A: port 8

Tail Role

Summary of Contents for EDS-505A Series


































































































































Search results

Summary of Contents for EDS-505A Series

Reviews:

Related manuals for EDS-505A Series

Brands by name

Popular brands

Moxa Technologies EDS-505A Series, User Manual

Search results

Summary of Contents for EDS-505A Series

Reviews:

Related manuals for EDS-505A Series

Brands by name

Popular brands