Moxa Technologies EDS-505A Series User Manual Download Page 73 | Manualshive

Page: 73 / 129

background image

EDS-508A/505A Series User’s Manual

Featured Functions

3-58

VLAN Mode

Setting

Description

Factory Default

802.1Q VLAN

Set VLAN mode to 802.1Q VLAN

Port-based VLAN Set VLAN mode to Port-based VLAN

802.1Q VLAN

Management VLAN ID

Setting

Description

Factory Default

VLAN ID ranges
from 1 to 4094

Set the management VLAN of this EDS.

1

Enable GVRP

Setting

Description

Factory Default

Enable/Disable

Select the option to enable/disable the GVRP
function.

Enable

Port Type

Setting

Description

Factory Default

Access

This port type is used to connect single devices
without tags.

Trunk

Select “Trunk” port type to connect another
802.1Q VLAN aware switch or another LAN that
combines tagged and/or untagged devices and/or
other switches/hubs.

Access

ATTENTION

For communication redundancy in the VLAN environment, set “Redundant Port,” “Coupling
Port,” and “Coupling Control Port” as “Trunk Port,” since these ports act as the “backbone” to
transmit all packets of different VLANs to different EDS units.

Port PVID

Setting

Description

Factory Default

VID range from 1
to 4094

Set the port default VLAN ID for untagged devices that
connect to the port.

1

Fixed VLAN List (Tagged)

Setting

Description

Factory Default

VID range from 1
to 4094

This field will be active only when selecting the “Trunk”
port type. Set the other VLAN ID for tagged devices that
connect to the “Trunk” port. Use commas to separate
different VIDs.

None

Forbidden VLAN List

Setting

Description

Factory Default

VID range from 1
to 4094

This field will be active only when selecting the “Trunk”
port type. Set the VLAN IDs that will not be supported
by this trunk port. Use commas to separate different
VIDs.

None

«
...
71
72
73
74
75
...
»

Summary of Contents for EDS-505A Series


































































































































Reviews:

No comments

Related manuals for EDS-505A Series

Professional Series

Brand: PACOM Pages: 15

EtherLink 3C509B

Brand: 3Com Pages: 8

Brand: 3Com Pages: 8

Brand: VMIC Pages: 126

Brand: Allied Telesis Pages: 22

Brand: XMOS Pages: 6

Brand: Glacier Pages: 2

Brand: Avenview Pages: 28

Brand: Navitar Pages: 1

Brand: LevelOne Pages: 3

NVR41-4KS2 Series

Brand: Dahua Pages: 452

Brand: ACTi Pages: 14

Brand: ATTO Technology Pages: 2

Brand: Dynamix Pages: 102

Brand: Intellinet Pages: 2

LinkStation 500

Brand: Buffalo Pages: 139

Brand: Xinje Pages: 76

Brand: Juniper Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands