manualshive.com logo in svg

Move Force+ 1000N, Installation Instructions And User Manual

Share
Download
Move Force+ 1000N Installation Instructions And User Manual Download Page 30

WARRANTY CERTIFICATE

NAME 

ADRESS

COUNTRY

PHONE

INSTALLER SIGNATURE AND STAMP

 

 

 

 

 

           

DATE             

-28

D

-

/ 

/ 

WARRANTY AND LIABILITY
Correct use and maintenance of automation is essential to ensure that the warranty is valid. The warranty has a period of two (2) years for 
residential users and one (1) year for industrial uses.
WARRANTY DOES NOT COVER:
Repairs performed by persons who are not properly trained and qualified.
Changes made to the construction and operation of the operator.
Damage caused by improper use.
Damage caused by lack of maintenance.
Damage caused by natural phenomena.

Portas Arcuense Lda, reserves the right to make changes to the products presented for the purpose of continuous improvement and development. All rights reserved to Portas Arcuense, Lda. Modifications or 
unauthorized use of this manual is forbidden without proper authorization.

Summary of Contents for Force+ 1000N

































Reviews:

No comments

Brands by name

Popular brands

Load more brands