NO
Date
Firmware
Version
Upgrade history
Hi-Manager
Software
Controller
Hardware
(Back of Unit)
27 2010.11.01
V2.14
P65 beep sound on/off added
V1.34
2.1
28 2010.12.08
V2.21
1) model added : HD-300L,500L,1000L
2) unit added : ozf-in ( HDC-30i only )
v1.36
2.1
29 2011.01.28
V2.3
P73 added : number of Preset # for selection by F1/F2 on screwdriver
( available when "3" selected on P71) F1 works for move up, F2
works for move down of preset # or model no. (Doga requested)
v1.37
2.1
30 2011.03.11
V2.4
1) bug solved : During sequence fastening by Model selecting, the last
count cancel by F2 button couldn't recall the last preset #.
2) modification : Delet the converted torque display on realtime
monitoring when stopped by angle(turn) --> request by Doga
v1.37
2.1
31 2011.04.06
V2.42
1) Every event on Multi-sequence will be displayed on realtime
monitoring
2) bug solved : torque setting in ozf.in on Hi-manager
v1.38
2.1
32 2011.04.14
V2.43
P63 : additional feature / calibration value (efficiency) can be wote on
P63. This value is saved on rom of screwdriver
v1.38
2.1
33 2011.05.27
V2.44.1
Model added - HD025P(SamsungTSOE request 0.6-2.5Kgf.cm /
harmoinized version between fimware and Hi-Manager
v2.44.1
2.1
34 2011.09.19
V2.45.0
Model added - HD400P / replacing HD450P by max torque difference
v2.45.0
2.1
35 2011.10.21
V2.46.0
1) Model added-HA025( for Samsung mobile new bit cushion and
calibration only)
2) Gear efficiency maximum
150% from 120%
3) Initialized for HDA025 as a standard driver
v2.46.0
2.1
36 2011.10.24
V2.46.1
No use
v2.46.0
2.1
37 2011.10.24
V2.46.2
The factory setting of P64 (I/O) is changed to "1" (IN/OUT for PLC) from
"0" for the driver model HD025, HDA025 is connected.
v2.46.0
2.1
38 2011.11.02
V2.47
P29 added. Cycle Reset by the Reset button on the front panel Enable
or Disable
v2.47.0
2.1
39 2011.12.22
V2.48
1) P64 I/O select - added "4. Connect to Socket Tray,
2) P78 modified to 1)No torque up before Min, 2) No torque up after Min,
3) No torque up in all cycle
v2.48.0
2.1
40 2012.03.30
V2.49
1) Model added - HD220J for Jabil project
torque range : 7 ~ 26 Kgf.cm
2) Parameter added- P30 : Reverse Enable/Disable
v2.48.0
2.1
41 2012.07.18
V2.50
Model added - HD081 for Samsung SESK. The torque range is same as
HD080. But it share the same design with HD150
v2.48.0
2.1
42 2012.03.30
V2.51
German languge added
v2.50.0
2.1
43 2013.01.15
V2.52
Model added - HD080C, HD150J for Jabil, Malaysia
080C : 2.2 ~ 7.5kgfcm / 150J : 4.0 ~ 15.0kgfcm
speed : 200 ~ 1000rpm
v2.52.2
2.1
44 2013.01.23
V2.53
Model added - HD150 V2, HD220 V2 for Jabil, Malaysia. V2 version
solved that the first torque was much higher than others.
v2.53.0
2.1
45 2013.04.02
V2.54.1
Max turn value was excluded in range -> changed it to be included in OK
range.
v2.53.0
2.1
46 2013.05.15
V2.54.4
Fastening data output / model no. output instead of preset # ( requested
by Torq-on for Denso monitoring program )
v2.53.0
2.1
47 2013.10.08
V2.55.1
New torque formula for V2J version in Jabil.
EZ-Torq II with Sehan RDA, Asian filter setting
v2.53.0
2.1
48 2013.11.21
2.55.2
Test version for Jabil
- HD060V2J and HD080V2J added
v2.53.0
2.1
49 2013.12.09
V2.55.3
model added : HD30N, HD45N, HD100N
v2.53.0
2.1
50 2013.12.19
V2.56.0
by Jabil request ( Only for V2J version )
- V2 has same torque formula with V1 in FW
- New torque spec of HD060V2J: 1.9~4.2 lbf.in
v2.53.0
2.1
51 2014.02.07
V2.56.2
- P88 : Soft/Hard joint select feature removed.
- P88 : Driver Lock (I/O) feature in direction
0 : Both direction
1 : Reverse direction Lock only
2 : Forward direction Lock only
v2.56.2
2.1
52 2014.05.23
V2.57
SCAN TIME change to 0.5s from 1.0s in programing
for short torque up signal time of HDC-35i
v2.56.2
2.1
53 2014.05.30
V2.58
Bit socket tray - selectable socket no. on P50
v2.57
2.1
54 2014.07.07
V2.58.2
- Torque range modification of HD081
2.5 - 8.0Kgf.cm --> 2.5 - 8.3Kgf.cm
by request of Doga
v2.57.2
2.1
55 2014.09.03
V2.58.5
LG- Special Request
v2.57.2E
2.1
56 2014.10.13
V2.60.0b
Automatic parmater reset to factory setting feature deleted when the
driver model is replaced. Manual paremeter reset is required when the
driver is replaced with the different model of driver.
v2.57.2E
2.1
57 2014.11.13
v2.60.2
1) parmeter P98 added : Start signal OFF delay time Special Request. 2)
Customer lost the fastening OK output when operator release start lever
just before torque up, but clutch was activated by innertia. range : 0 -
1,000 mS factory setting : 10mS. 3) Motor immediate stop by breaking
when start signal OFF.
v2.57.5E
2.1
58 2015.04.06
v2.61.0
1) F/R status OUT signal change (Forward :1, Reverse:0 --> Forward:0,
Reverse:1), 2) UP button is available to select Model no. when P75 is
enabled. 3) Operation change / Unless other model no. was not
selected, the latest loaded model no. is continuously effective even if it's
program was changed. 4) The lowest torque setting range is changed
from 7 to 5 Kgf.cm for HD220 & HD220P.
v2.57.6E
2.2
2015.04.06
v2.61.1
Fastening Min. Max angle error does not provide angle data output
v2.57.6E
2.2
59 2015.05.14
v2.61.2
solved Socket tray bug.
v2.57.6E
2.2
60 2015-05-22
v2.61.3
Converted torque(E308) error bug fix.
v2.57.6E
2.2
HDC Firmware / Hi-Manager Upgrade History by version
1080 N 11th St San Jose CA 95112
www.mountztorque.com 408.292.2214
89
