Motorola SYMBOL DS3578 Product Reference Manual Download | Manualshive

Page: 64 / 430

background image

4 - 14 DS3578 With FIPS Digital Scanner Product Reference Guide

Auto-reconnect Feature

When in SPP Master or Cradle Host mode, the digital scanner automatically tries to reconnect to a remote device
when a disconnection occurs that is due to the radio losing communication. This can happen if the digital scanner
goes out of range with the remote device, or if the remote device powers down. The digital scanner tries to
reconnect for the period of time specified by the Reconnect Attempt Interval setting. During that time the green
LED continues to blink.

If the auto-reconnect process fails due to page timeouts, the digital scanner’s LED is red and sounds a page
timeout beep (long low/long high) and enters low power mode. The auto-reconnect process can be re-started by
pulling the digital scanner trigger.

If the auto-reconnect process fails because the remote device rejects the connection attempt, the digital scanner
sounds a connection reject beep sequence (see

Wireless Beeper Definitions on page 4-3

) and deletes the remote

pairing address. If this happens, a pairing bar code must be scanned to attempt a new connection to the remote
device.

The digital scanner has memory available for storing a remote Bluetooth address for each Master mode (SPP,
Cradle). When switching between these modes, the digital scanner automatically tries to reconnect to the last
device it was connected to in that mode.

Reconnect Attempt Beep Feedback

When a digital scanner disconnects as it goes out of range, it immediately attempts to reconnect. While the digital
scanner attempts to reconnect, the green LED continues to blink. If the auto-reconnect process fails, the digital
scanner emits a page timeout beep (long low/long high) and stops blinking the LED. The process can be restarted
by pulling the trigger.

The Beep on Reconnect Attempt feature is disabled by default. When enabled, the digital scanner emits 5 short
high beeps every 5 seconds while the reconnection attempt is in progress.

Scan a bar code below to enable or disable Beep on Reconnect Attempt.

NOTE

If a bar code is scanned while the auto-reconnect sequence is in process, a transmission error beep
sequence sounds and the data is not transmitted to the host. After a connection is reestablished, normal
scanning operation returns. For error beep sequence definitions, see

Beeper Definitions on page 2-1

NOTE

Switching between Bluetooth host types by scanning a host type bar code (

) causes the radio to

be reset. Scanning is disabled during this time. It takes several seconds for the digital scanner to
re-initialize the radio at which time scanning is enabled.

*Disable Beep on Reconnect Attempt

Enable Beep on Reconnect Attempt

«
...
62
63
64
65
66
...
»

Summary of Contents for SYMBOL DS3578















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SYMBOL DS3578

Brand: Thinkcar Pages: 5

Brand: Icarus Pages: 13

Brand: Fametech Pages: 50

RoadRunners BRR-L

Brand: Baracoda Pages: 48

Brand: Atid Pages: 15

Brand: Atid Pages: 46

Brand: Argox Pages: 32

Brand: Argox Pages: 47

MS860 Bluetooth

Brand: Unitech Pages: 2

Brand: Unitech Pages: 2

MS852 Auto Switching

Brand: Unitech Pages: 2

Brand: Tyro Pages: 14

Brand: IVDT Pages: 13

Brand: ViewSonic Pages: 73

Brand: Hand Held Products Pages: 2

Cipher 1660 BT Portable

Brand: Dataman Pages: 9

Brand: EntraPass Pages: 2

Brand: Sonnet Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands