manualshive.com logo in svg

Motorola MVME172, Programmer'S Reference Manual

The Motorola MVME172 Programmer's Reference Manual is a comprehensive manual providing detailed instructions and information for programming this high-performance device. Available for free download from our website, it offers programmers easy access to essential information to maximize the potential of the MVME172.

Share
Download
background image

GCSR Programming Model

http://www.mcg.mot.com/literature

2-103

2

Programming the GCSR

A complete description of the GCSR is provided in the following tables. 
Each register definition includes a table with five lines. 

❏

Line 1 is the base address of the register as viewed from the local 
bus and as viewed from the VMEbus, and the number of bits defined 
in the table. 

❏

Line 2 shows the bits defined by this table. 

❏

Line 3 defines the name of the register or the name of the bits in the 
register. 

❏

Line 4 defines the operations possible on the register bits as follows: 

❏

Line 5 defines the state of the bit following a reset as defined below: 

R

This bit is a read-only status bit. 

R/W

This bit is readable and writable. 

S/R

Writing a one to this bit sets it. Reading it returns its current 
status. 

P

This bit is affected by power-up reset. 

S

The bit is affected by SYSRESET. 

L

The bit is affected by local bus reset. 

X

The bit is not affected by reset. 

Summary of Contents for MVME172



































































































































































































































































































































































Reviews:

No comments

Related manuals for MVME172

Saitek P880 User Manual preview
P880
Brand: Saitek Pages: 44
Radarcan R-200 User Manual preview
R-200
Brand: Radarcan Pages: 40
tams elektronik HELIOS Manual preview
HELIOS
Brand: tams elektronik Pages: 60
Lamtec ETAMATIC Manual preview
ETAMATIC
Brand: Lamtec Pages: 136
SAI HVAC Compact Comfort VAV12 User Manual preview
Compact Comfort VAV12
Brand: SAI HVAC Pages: 16
Saitek Pacific AV8R Manual preview
Pacific AV8R
Brand: Saitek Pages: 15
saia-burgess PCD3 Series Hardware Manual preview
PCD3 Series
Brand: saia-burgess Pages: 203
Sailor N420 Technical Manual preview
N420
Brand: Sailor Pages: 1
Ublox EVK-W262U Quick Start preview
EVK-W262U
Brand: Ublox Pages: 2
u-blox NINA-B1 Series Getting Started preview
NINA-B1 Series
Brand: u-blox Pages: 19
Vaillant VRT 340f Operating Instruction preview
VRT 340f
Brand: Vaillant Pages: 32
Vaillant VRT 330 Manual preview
VRT 330
Brand: Vaillant Pages: 27
Vaillant VRC 470 Operating Instructions Manual preview
VRC 470
Brand: Vaillant Pages: 40
Vaillant VRT 350f Installation Instructions Manual preview
VRT 350f
Brand: Vaillant Pages: 36
Vaillant VRT 350 Installation Instructions Manual preview
VRT 350
Brand: Vaillant Pages: 28
Vaillant VAZ CPC Operating Instructions Manual preview
VAZ CPC
Brand: Vaillant Pages: 92
WAREMA Wisotronic Operating Instructions Manual preview
Wisotronic
Brand: WAREMA Pages: 112
WAGO 750-880 Manual preview
750-880
Brand: WAGO Pages: 414

Brands by name

Popular brands

Load more brands