background image

Rear brake lever (Pic 4) 
Pull the lever to work the rear brakes. 

Dim/Dip Switch (4) 

 
When the switch is on “ ” position the front lamp main beam is ON. When the switch 
is  on “

” position the front lamp dipped beam is ON and main beam indicator light 

should be extinguished. 

 

Turn signal switch (2) 

Sliding the switch to the “ ” position will illuminate the left turn signal. Sliding the 

switch to the “ ” position will illuminate the right turn signal. To switch off the turn 
signals press the switch “(3)”. 

 

.Warning : 
Always use the signal when you intend to change lanes or make a turn. Always be sure 
to turn the signal switch to the off position after completing the turn or lane change so 
not to confuse other road users. 

 

Horn button

 

(1) 

Press the switch to operate the horn. 
 

Right handlebar control system (Pic 7)   

Kill switch (1) 
“ ” means you can start the engine any time. 
“ ” (close) means you cannot start the engine. 
 

Electric starter button

 

(2) 

This  button  is  used  to  start  the  engine.  Turn  the  ignition  key  to  the  ON  position, 
squeeze the rear brake lever and press the start button, the engine will now start. 
 

Front brake lever 

Pull the lever to work the front brake. 

 

Throttle control (Pic 21) 

The right hand twist grip controls the engine speed. 
 
 
 
 
 
 
 
 
 

Summary of Contents for XO 125





























Reviews: