mori seiki NL1500/500, Maintenance Manual

Page: 229 / 245

229
ʎ˂ʵʡʴʅʍʉʃʉɮʳʃʠʶ˂ɹʃʐʪɁ̬૰
TOOL PRESETTER STYLUS BREAK STEM REPLACEMENT
4)
ʃʉɮʳʃȟ
Z
ᢉȾࢲᚐȾ՘ɝ͇ȤɜɟȹȗȽȗکնǾʃ
ʉɮʳʃɥوᢆȨȮǾ
Z
ᢉȾࢲᚐȾȽɞɛșȾᝩ୥Ȭɞǿ
4)
If the stylus is not accurately set parallel to the Z-axis, turn
the stylus so that it is parallel to the Z-axis.
a)
M3
Ɂфᜏሰ͇Ƞඨɔɀȫɥ፿ɔɞǿ
a)
Loosen the M3 socket set screw.
b)
ʃʉɮʳʃɥوᢆȨȮǾȺȠɞȳȤ
Z
ᢉȾࢲᚐȾȽɞ
ɛșȾᝩ୥Ȭɞǿ
b)
Turn the stylus to adjust its parallelism with the Z-axis.
c)
M3
Ɂфᜏሰ͇Ƞඨɔɀȫɥ፻ɔɞǿ
c)
Tighten the M3 socket set screw.
d)
M5
Ɂфᜏሰ͇Ƞඨɔɀȫɥ̬̠Ⱦ፻ɔȲɝ፿ɔȲɝ
ȪȹǾوᢆ஁տɁॊᝩ୥ɥᚐșǿ
d)
Tighten and loosen the two M5 socket set screw
alternately to achieve fine adjustment.
2
าᜤ
2
NOTE
ʊɮʮʵɼ˂ʂɁᦉɁӦȢᦀȟǾ
0.005 mm
͏юȾȽɞɛșᝩ୥
ȪȹȢȳȨȗǿ
The allowable maximum inclination is 0.005 mm over the entire
length of the stylus side face.
5)
ᝩ୥ȟީ̘ȪȲɜǾ
M5
Ɂфᜏሰ͇Ƞඨɔɀȫɥ
4.5 N•m
Ⱥۄ፻ɔɥȬɞǿ
5)
After the completion of adjustments, finally tighten the M5
socket set screw with a torque of 4.5 N•m.
1
ʎ˂ʵʡʴʅʍʉɁʛʳʫ˂ʉᛃඩϏɁᝩ୥஁ศȾȷȗȹ
ɂǾҝёૄ͇ᝢ஥ం
“
ൡಽૄ͇ऻɁʎ˂ʵʡʴʅʍʉᝩ୥
஁ศ
”
1
Refer to the separate volume, INSTALLATION MANUAL,
"ADJUSTING TOOL PRESETTER AFTER MACHINE
INSTALLATION" for setting the tool presetter parameter.