Morgana DIGIFOLD Operating Manual Download Page 28 | Manualshive

Page: 28 / 40

background image

Replacing Blade Sets

11.

Push the exit guard down and replace the delivery assembly before operating the

machine.

12.

Switch the machine on and test the crease for form.

In the event of any damaged or lost components within the blade assembly, spares kits
are available on request. However, components within the blade set can not be ordered
separately i.e. single blade or anvil.

Consisting of a standard blade and anvil, blade brushes, blade links and alignment bolts.

If the pressure and the alignment of the crease is not to a satisfactory level,
see pages 25 and 26 to adjust the creasing line.

Standard Blade set (fitted to Digifold as standard)

Part number 76-213-01

‘Spares’ kits

Extra Narrow Blade set (optional)

Part number 76-213-03

Consisting of a special extra narrow anvil, a standard blade, blade brushes, blade links
and alignment bolts.

Page 28

CREASING / FOLDING

«
...
26
27
28
29
30
...
»

Summary of Contents for DIGIFOLD









































Reviews:

No comments

Related manuals for DIGIFOLD

Brand: Singer Pages: 10

Brand: Strobel Pages: 78

Brand: Janome Pages: 22

Brand: Janome Pages: 2

Brand: Sinbo Pages: 48

Brand: KISANKRAFT Pages: 14

Brand: Carina Pages: 30

Advolution UHR 70-1700

Brand: Nilfisk-Advance Pages: 32

Brand: BRONDI Pages: 32

Advenger 2800ST

Brand: Nilfisk-Advance Pages: 104

Brand: JUKI Pages: 100

Brand: Husqvarna Pages: 76

Brand: Husqvarna Pages: 92

Brand: Husqvarna Pages: 100

Brand: Husqvarna Pages: 80

Brand: Husqvarna Pages: 84

Brand: Husqvarna Pages: 100

Brand: Husqvarna Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands