Mooney M20TN, Service And Maintenance Manual

Page: 227 / 1169

MOONEY AVIATION COMPANY, INC.
M20TN SERVICE & MAINTENANCE MANUAL
Page
Date
15
2006
Rev Date
8. Disconnect the Cable Interface Assembly from the
EMA (Figure 25--4) by depressing locking mechanism,
releasing the connector halves.
SAA
CONNECTORS
EMA
CONNECTOR
DIAGNOSTIC
CONNECTOR
CABLE
INTERFACE
ASSEMBLY
LOCKING TABS
ELECTRICAL AND HOSE CONNECTOR OF IN-
FLATOR ASSEMBLY
FIGURE 25--4
9. Remove Cable Interface Assembly.
10. Remove EMA from mounting hardware (Aftermar-
ket installations, refer to AmSafe Installation drawings
509760 -- pilot, co-- pilot seats or 509780 -- passenger
seats).
Replacement
Replace all AAIR components with same part number
as that of removed assembly. (for Aftermarket installa-
tions, refer to AmSafe Installation drawings 509760 --
pilot--co--pilot seats or 509780 -- passenger seats, or
SICA Parts List to define cable routing.
-- WARNING --
AVOID MAGNETIC FIELDS AT ALL TIMES IN THE
VICINITY OF THE EMA. DEPLOYMENT OF THE
SYSTEM MAY OCCUR.
1. Before replacing new Inflator(s) Assy(s), unscrew
the Shipping Cap from the Inflator hose fitting (Figure
25--2). Do not discard Shipping Cap , it is used for
shipping the Inflator Assy. When installing cap torque to
5 -- 10 in. lbs (.56 -- 1.13 Nm). Contact AmSafe at
www.amsafe.com or (602) 850.2850 for detailed ship-
ping information.
2. Insert prepared Inflator Assy(s) into mounting brack-
ets. Do not secure in mounting bracket at this time.
3. Remove the end cap plug (if new SAA) from Three--
Point Airbag Belt(s) gas hose and discard. DO NOT
REMOVE Safety Cable Tie for airbag connector tongue
at this time.
-- CAUTION --
Check orientation of Three--Point Seatbelt Airbag
Belt(s) before inserting gas hose into Inflator.
Gas hose should be protruding on top of seatbelt
attachment hardware. Airbag cover must present
away from occupant (label orientation is on in-
side towards occupant). (for Aftermarket installa-
tions, refer to AmSafe Installation drawings
509760 -- pilot--co--pilot seats or 509780
passenger seats).
NOTE:
Apply a thin, even coat of Loctite 242 thread lock-
ing compound on the hose barb threads before
attaching to Inflator Assy.
4. Connect gas hose from Three--Point Airbag Belt(s)
to Inflator(s) using required in/lbs torque 110--130 in.
lbs (12.43 -- 14.69Nm). The Inflator(s) hose connector
fitting (Figure 25--3) is a pressure fitting which must be
fully seated (fitting fully extended) onto the gas hose
barb for an air--tight fit.
5. Attach Squib Connector(s) (Figure 25--3) to Inflat-
or(s). Orient connector as shown in Figure 25--3 and
seat into inflator until it locks in place.
6. Secure the Inflator Assy(s) within its original position
on the mounting hardware.
NOTE:
Do not damage any portion of TRW serial number
on Inflator when mounting.
7. Insert EMA (50) into mounting hardware and secure
(for EMA installation hardware torque values, refer to
Mooney installation instructions/drawing 140345, Re-
straint Instl -- Airbag, (for Aftermarket installations, Am-
Safe Installation drawings 509760 -- pilot--co--pilot
seats or 509780 -- passenger seats). The arrow on the
EMA label should face aircraft forward (see Figure
25--5). Connect EMA to Cable Interface Assy’s EMA
connector. The connectors are keyed. Align connector
halves and seat fully until they lock.
25--10--03
AUGUST 2010