Moog SmartMotor Developer'S Manual Download Page 230 | Manualshive

Page: 230 / 909

background image

P

ar

t

1: P

rog

ra

m

ming

Moog Animatics SmartMotor™ Developer's Guide, Rev. L

Page 230 of 909

The following table provides a matrix of the index capture functions for the M-style motors.

Capture

Internal index input

a

External index

input

b

Disable index

input

c

Internal encoder

EIRE command (default
at startup)

EIRI command

Not supported

External encoder

Not supported

EIRE command
(default at startup)

EIRI command

a) From the internal encoder
b) I/O port 5, single-ended, 24 volts
c) Disables capture on indicated encoder

For additional information on index capture, see Index Capture Commands on page 128. For
more details, see Part 2: SmartMotor Command Reference on page 238.

I/O Port 6 – Go Command

The following command is used to issue a G (Go) command:

EISM(6)

Issues G when specified I/O goes low

I/O Brake Output Commands

The brake output function can be configured to any I/O port including the expanded I/O ports
where IO is the bit number.

The following commands are used to configure the brake output:

EOBK(IO)

Configure a given output to control an external brake

EOBK(-1)

Remove the brake function from the I/O port

For more details, see Part 2: SmartMotor Command Reference on page 238.

I²C Expansion (D-Style Motors)

I/O ports 4 and 5 can perform as an I²C port. I²C is an "Inter-IC-Communication" scheme that
is simple and powerful. There are dozens of low-cost I²C devices on the market that message
over I²C and deliver many resources. I²C chips include: I/O expanders, analog input and
output, nonvolatile memory, temperature sensors, etc. I²C provides a low cost means of
expanding the functionality of a SmartMotor. For more details on I²C, see I²C
Communications (D-Style Motors) on page 115.

Part 1: Programming: I/O Port 6 – Go Command

«
...
228
229
230
231
232
...
»

Summary of Contents for SmartMotor














































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartMotor

EtherCAT CoolDrive RC Series

Brand: Tsino Dynatron Pages: 278

Brand: TQ Pages: 28

ECI-42 K1 Series

Brand: ebm-papst Pages: 28

Brand: Yamaha Pages: 13

JA comfort SMI series

Brand: elero Pages: 6

Torque-Hub 18HC00 Series

Brand: Oerlikon Fairfield Pages: 46

Allen-Bradley PowerFlex 4 22A-A1P4N103

Brand: Rockwell Automation Pages: 88

CNMD180W0ENNNC1

Brand: Rockwell Automation Pages: 248

Brand: Iomega Pages: 32

Brand: HAUTAU Pages: 8

Brand: ZIEHL-ABEGG Pages: 123

Brand: fakro Pages: 8

Brand: Applied Motion Products Pages: 2

Brand: ICAN Pages: 16

VLT Midi Drive FC 280

Brand: Danfoss Pages: 4

Brand: ZIEHL-ABEGG Pages: 204

Brand: YASKAWA Pages: 182

Brand: TDE MACNO Pages: 134

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands