background image

Moog Components Group 

Mini4, Rev C 

February 23, 2009

 

(201580-xxx And 201590-xxx) 

 

Page  16 of 19 

 

1.3.6

 

Power Section Testing 

 

NOTE:  There are connectors on the bottom of the Video Input and Output boards have pins that are 
connected  to  +5VDC  and  ground.    If  these  pins  are  inadvertently  shorted  together  or  to  a  common 
chassis ground, the board fuse (F3 on Input/F4 on Output) will blow. 

 
If the +5V Power LED, +3.3V Power LED and +2.5V Power LED are out: 

 

Check for continuity of fuse F3/41 with an ohmmeter. 

 

Replace fuse if damaged.   

 
If only the +3.3V Power LED is out: 

 

5VDC across C42 (replace board if +5VDC is not available) 

 

3.3VDC across C40 on top of board 

 

If +3.3V is not available replace the board with a spare. 

 

If +3.3V is available check the display LED (D7). 

 
If only the +2.5V Power LED is out: 

 

5VDC across C35 (replace board if +5VDC is not available) 

 

2.5VDC across C47 on back of board 

 

If +2.5V is not available replace the board with a spare. 

 

If +2.5V is available check the display LED (D6). 

 
If D1 is not on and Daughterboarrd operation is required: 

 

Verify that either F6 (for +3.3VDC to D/B) or F5 (for +5VDC to D/B) is placed and is not blown 

 

Replace fuse if damaged (it is a surface mount) 

 

Verify proper voltage at connector J1 

 

If Voltage is available check the display LED (D1). 

 

 

1.3.7

 

Optical Section Testing 

 
If the FIBER LED, RMT LINK LED and/or LOC LINK LED are off or flickering, one or more of the 
following conditions is likely: 

 

The fiber is broken or damaged. 

 

The optical transceiver module is defective.  

 

Excessive light loss (low received optical power) is being experienced.  

 

The Mini4 board (not the optical transceiver module) is malfunctioning. 

 

There is not enough attenuation in the optical link and the receiver is saturating. 

 
If excessive optical loss is being experienced, the following conditions may be present: 

 

May have horizontal lines or random white dots on video monitors. 

 

Check  the  optical  level  with  an  optical  power  meter  and  inspect  all  fiber  optic  connections 
including WDM/CWDMs and slip rings. 

 

Summary of Contents for PRIZM Mini4 Series




















Reviews: