Before installing new faucet make sure that the cartridge nuts are in place.
The cartridge and cartridge nuts were properly installed and tested before
leaving the factory. Although it is unlikely, it is nevertheless possible that
through the handling of the valve by any number of persons the cartridge
nuts may not be properly installed. This should be carefully checked at time
of installation. If the cartridge nuts are not properly installed, water pressure
could force the cartridge out of the casting. Personal injury or water damage
to the premises could result.
1. Insert head of spout bolt (6) into the slot at the back of the valve body (7).
With the ears of the mounting bracket (5) facing up, screw in the spout
tube (9) with the longer unthreaded end up. Mounting bracket (5) should
be approximately 1/2" up from spout tube (9). A 7/32" hex wrench is
supplied. Lubricate both spout tube o-rings (A) with silicone grease
supplied, position the mounting bracket over spout bolt and insert spout
tube into valve body.
INSTALLATION INSTRUCTIONS
2. Apply plumber’s putty (not supplied) to bottom of top
mounting washers (4). Center washers over holes in deck.
Slide valve assembly from under the deck up through
sink/deck holes, washers. Insert retaining clips (3) into lower
grooves on valve assembly. Release valve assembly down
until it rests on top of the washers. Place the 7/32" hex key
wrench into the tube bolt (6) and tighten mounting bracket
securely.
1
2
2
A. Lavatory Waste Installation
Instructions
1)
Thoroughly clean around drain
opening of lavatory sink.
2)
Apply plumbers putty under seat
(2).
3)
Thread mounting nut (5),
mounting washer (4) and bottom
gasket (3) onto drain body (6).
Wrap top threaded end of drain
body with Teflon tape (15).
4)
Position drain body up through
drain opening and screw seat
onto drain body.
5)
Align drain body so that pivot rod
opening faces the rear of the
sink and tighten the mounting
nut snug.
6)
Apply Teflon tape to the threaded
end of the tailpiece (12) and
screw into the drain body.
Tighten firmly by hand.
7)
Drop in plug base (1) and install
pivot rod in one of the following
ways:
I.
Vandal proof:
Prevent
unauthorized removal of drain
plug. Place pivot rod seat (7) into
opening of drain body as shown.
Place the pivot rod (14) into the
opening and position the pivot
rod through the upper hole of the
pop-up base as shown in
installation (a). Slide the pivot nut
onto the pivot rod and thread
snugly onto the drain body, be
careful not to over tighten.
II.
Easy removal: After inserting
drain plug into waste tube, turn
drain plug 90 degrees. For quick
removal of drain plug for
cleaning, follow the instructions
above except position parts as
shown in illustration (b) above.
Do not insert pivot rod into
opening of pop-up base.
8)
Connect the pivot rod (14) to lift
rod strap using spring clip (11)
as shown above.
To disassemble waste assembly,
reverse steps as listed above. In
order to remove seat cover, use
screwdriver to bend snap features
back from the inside as shown in
picture. Do not try to lift seat cover
with tool from the outside.
B. Lavatory Waste Installation
Instruction
1)
Thoroughly clean around drain
opening of lavatory sink.
2)
Apply plumbers putty under seat
(2).
3)
Drop seat into the drain opening
in sink.
4)
From underneath the sink. Slide
bottom gasket (3), mounting
washer (4) and mounting nut (5)
onto drain seat and hand tighten.
5)
Fit seal (12) inside the drain
tailpiece (6).
6)
Install the tailpiece and hand
tighten. Align the entire assembly
so that the pivot rod is facing the
rear of the sink, hand tighten the
mounting nut (5) until snug.
7)
Drop in plug base (1) and install
pivot rod in one of the following
ways:
III. Vandal proof:
Prevent
unauthorized removal of drain
plug. Place pivot rod seat (2) into
opening of drain body as shown.
Place the pivot rod (14) into the
opening and position the pivot
rod through the upper hole of the
pop-up base as shown in
installation (a). Slide the pivot nut
onto the pivot rod and thread
snugly onto the drain body, be
careful not to over tighten.
IV. Easy removal:
For quick
removal of drain plug for
cleaning, follow the instructions
above except position parts as
shown in illustration (b) above.
Do not insert pivot rod into
opening of pop-up base.
8)
Connect the pivot rod (14) to lift
rod strap using spring clip (11)
as shown above.
To disassemble waste assembly,
reverse steps as listed above. In
order to remove seat cover, use
screwdriver to bend snap features
back from the inside as shown in
picture below. Do not try to lift seat
cover with tool from the outside.
A
B
1
2
4
3
6
7
8
9
14
10
11
12
5
13
15
15
1 Drain Plug Base Part
2 Seat
3 Bottom Gasket
4 Mounting Washer
5 Mounting Nut
6 Drain Body
7 Pivot Rod Seat
8 Pivot Nut
9 Lift Rod Strap
10 Lift Rod Strap Screw
11 Spring Clip
12 Tailpiece
13 Plumbers Putty
14 Pivot Rod
15 Teflon Tape
4
18
18
(a)
(b)
4
1 Drain Plug Base Part
2 Seat
3 Bottom Gasket
4 Mounting Washer
5 Mounting Nut
6 Tail Piece
7 Pivot Rod Seat
8 Pivot Nut
9 Lift Rod Strap
10 Lift Rod Strap Screw
11 Spring Clip
12 Seal
13 Plumbers Putty
14 Pivot Rod
4
18
18
(a)
(b)
4
1
2
4
3
6
7
8
12
9
10
11
5
14
13
7
6
5
9
4
6
3
