MMM MINITAUR Diy Manual Download Page 30 | Manualshive

Page: 30 / 30

background image

Step#6

Step#6

Now double check your USB cable and connect accordingly. You will notice that the last
black wire connects to nothing. That is ok, it is the shield of the USB connector. I see no
reason to introduce any digital noise into your signal via your metal rack.

Please mark the red connector side with the red connector side wire that you just soldered.
Now test your USB cable and your MIDI cable again.

If you have no problems, please use some electrical tape, or shrink wrap to protect the
exposed wires.

If you do have any problems or questions, please contact me at
[email protected]

Thank you for your

support!

«
...
28
29
30

Summary of Contents for MINITAUR































Reviews:

No comments

Related manuals for MINITAUR

Brand: Boss Pages: 72

Brand: Oster Pages: 14

Brand: GameChanger Audio Pages: 8

Spectrum Enhancer SE200

Brand: Behringer Pages: 2

Brand: Behringer Pages: 11

Brand: Windmere Pages: 2

Brand: HP Pages: 27

Brand: HP Pages: 107

Brand: Sound Devices Pages: 84

Brand: A.G. PULIE Pages: 7

Brand: Blackstar Pages: 16

Brand: Fulltone Pages: 2

Brand: Yamaha Pages: 2

Brand: Yamaha Pages: 4

Brand: Yamaha Pages: 7

MG102C - 10 Input Stereo Mixer

Brand: Yamaha Pages: 21

Brand: Yamaha Pages: 8

Brand: Yamaha Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands