background image

SELF-TEST FUNCTION

WARNING

When first connected to the mains supply, the fitting will carry out an initial 3-second function test. Any faults 
will be indicated by the bi-colour LED indicator. 
This product is programmed to carry out its own self-test operation according to the following programme:

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance 
testing. Irreparable damage will occur if this instruction is not followed.

The test button on the side of the fitting can also be used to initiate functional testing as required – the 
luminaire will go into emergency mode while the test button is held in.
Following self-tests, the unit will revert to charging mode, and any faults will be indicated by the bi-colour 
LED indicator as follows:

 To clear a fault indication, switch off the power to the luminaire and then hold the test button for 10 seconds.

 

SELF-TEST FUNCTION 

When first connected to the mains supply, the fitting will carry out an initial 3-second function test. Any faults will 

be indicated by the bi-colour LED indicator.  

This product is programmed to carry out its own self-test operation according to the following programme: 

Every 30 days 

10-second function test 

Every 180 days 

3-hour duration test 

The test button on the side of the fitting can also be used to initiate functional testing as required – the luminaire 

will go into emergency mode while the test button is held in. 

Following self-tests, the unit will revert to charging mode, and any faults will be indicated by the bi-colour LED 

indicator as follows: 

LED indicator 

Status 

Slow flash green (3 sec on, 1 sec off) 

Charging 

Solid green 

Fully charged 

Fast flash green (0.1 sec on, 0.1 sec off) 

Function test underway 

Slow flash green (1 sec on, 1 sec off) 

Duration test underway 

Solid red 

Lamp fault (open circuit / short circuit) 

Slow flash red (1 sec on, 1 sec off) 

Battery fault or failed duration test 

Indicator off 

Emergency mode 

 To clear a fault indication, switch off the power to the luminaire and then hold the test button for 10 seconds. 

WARNING 

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance 

testing. Irreparable damage will occur if this instruction is not followed. 

GENERAL 

This product contains a light source of energy efficiency class D to Regulation (EU) No. 2019/2015 and (UK)

 

2021 No. 1095. 

This product contains a non-replaceable LED light source and a control gear which can be replaced by a 

professional. 

 

 

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the 

product. 

Installing in areas where the temperature consistently drops below 0°C may shorten the battery life. 

 

SELF-TEST FUNCTION 

When first connected to the mains supply, the fitting will carry out an initial 3-second function test. Any faults will 

be indicated by the bi-colour LED indicator.  

This product is programmed to carry out its own self-test operation according to the following programme: 

Every 30 days 

10-second function test 

Every 180 days 

3-hour duration test 

The test button on the side of the fitting can also be used to initiate functional testing as required – the luminaire 

will go into emergency mode while the test button is held in. 

Following self-tests, the unit will revert to charging mode, and any faults will be indicated by the bi-colour LED 

indicator as follows: 

LED indicator 

Status 

Slow flash green (3 sec on, 1 sec off) 

Charging 

Solid green 

Fully charged 

Fast flash green (0.1 sec on, 0.1 sec off) 

Function test underway 

Slow flash green (1 sec on, 1 sec off) 

Duration test underway 

Solid red 

Lamp fault (open circuit / short circuit) 

Slow flash red (1 sec on, 1 sec off) 

Battery fault or failed duration test 

Indicator off 

Emergency mode 

 To clear a fault indication, switch off the power to the luminaire and then hold the test button for 10 seconds. 

WARNING 

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance 

testing. Irreparable damage will occur if this instruction is not followed. 

GENERAL 

This product contains a light source of energy efficiency class D to Regulation (EU) No. 2019/2015 and (UK)

 

2021 No. 1095. 

This product contains a non-replaceable LED light source and a control gear which can be replaced by a 

professional. 

 

 

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the 

product. 

Installing in areas where the temperature consistently drops below 0°C may shorten the battery life. 

Summary of Contents for BATSCWMST4











Reviews: