Fig. 2
• Mark the location of the fixing holes and drill the holes ensuring not to infringe with any gas/water pipes or
electrical cables. The fitting can also be mounted over conduit boxes – the distance between fixing centres
is 600mm
• Feed the mains cable through the cable entry point, and secure the luminaire to the surface
• Ensuring correct polarity is observed, carefully wire as shown in Fig. 2. Two cables can be inserted into the
push-fit terminal block in order to achieve loop-in/loop-out wiring
• Connect the battery to the inverter
• Select the desired driver output and colour temperature (see Fig. 3)
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following products:
BATSCDA4 / BATSCDA5 / BATSCDA6
SAFETY
•
This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•
Please isolate mains prior to installation or maintenance
•
Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse or circuit breaker
•
Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
•
This product is for indoor use only
•
This product is Class I and must be earthed
•
This product is IP20 rated
INSTALLATION
•
Provide power to the required point of installation
•
Squeeze the sides and hinge the diffuser away from the fitting (see Fig. 1)
Fig. 1
•
Mark the location of the fixing holes and drill the holes ensuring not to infringe with any gas/water pipes
or electrical cables. The fitting can also be mounted over conduit boxes – the distance between fixing
centres is 600mm
•
Feed the mains cable through the cable entry point, and secure the luminaire to the surface
•
Ensuring correct polarity is observed, carefully wire as shown in Fig. 2. Two cables can be inserted into
the push-fit terminal block in order to achieve loop-in/loop-out wiring
Fig. 2
•
Select the desired colour temperature (see Fig. 3)
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following products:
BATSCWMST4 / BATSCWMST5 / BATSCWMST6
SAFETY
•
This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•
Please isolate mains prior to installation or maintenance
•
Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse or circuit breaker
•
Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
•
This product is for indoor use only
•
This product is Class I and must be earthed
•
This product is IP20 rated
INSTALLATION
Note - Microwave sensors may not be suitable for all installations, for example enclosed spaces, as they are
able to detect movement through non-metallic surfaces like plasterboard and thin doors.
•
Provide power to the required point of installation
•
Squeeze the sides and hinge the diffuser away from the fitting (see Fig. 1)
Fig. 1
•
Mark the location of the fixing holes and drill the holes ensuring not to infringe with any gas/water pipes
or electrical cables. The fitting can also be mounted over conduit boxes – the distance between fixing
centres is 600mm
•
Feed the mains cable through the cable entry point, and secure the luminaire to the surface
•
Ensuring correct polarity is observed, carefully wire as shown in Fig. 2. Two cables can be inserted into
the push-fit terminal block in order to achieve loop-in/loop-out wiring
Fig. 2
•
Connect the battery to the inverter
•
Select the desired driver output and colour temperature (see Fig. 3)
Fig. 1
