MK Diamond Products 160028 Owner'S Manual & Parts List Download Page 6

6

MK-377EXP SAW                                                                                           SAFETY

Consult the owner’s manual for recommended accessories.  Using improper accessories 

may increase the risk of personal or by-stander injury. Unauthorized equipment 

modifications will void all warranties. Manufacturer does not assume responsibility for any 

accident due to equipment modifications.

ALWAYS

 ensure that the machine is on level ground before using.

Serious injury could occur if a power tool is tipped, or if a cutting tool is unintentionally 

contacted.

When loading or unloading the machine, use caution. Remove the blade prior to hoisting, 

loading and transporting the machine.

USE RECOMMENDED ACCESSORIES

NEVER STAND ON THE TOOL

TRANSPORT

Form a habit of checking to see that keys and adjusting wrenches are removed from 

the power tool before it is turned on.

Cluttered work areas and benches invite accidents. Keep area around machine clear of 

obstructions which could cause persons to fall.

DO NOT

 operate equipment in dangerous or hazardous environments. 

DO NOT

 use power 

tools in damp or wet locations nor expose them to rain.  Always keep the work area well 

lighted. 

REMOVE ADJUSTING KEYS AND WRENCHES

KEEP WORK AREA CLEAN

DO NOT USE IN DANGEROUS PLACES

MAINTAIN TOOLS WITH CARE

Keep tools clean and maintained for the best and safest performance. Always follow 

maintenance instructions and examine the machine before use. If any abnormal vibrations 

or noises occurs, turn off machine immediately and have the problem corrected before 

further use.

DISCONNECT TOOLS

Power tools should always be disconnected before servicing, adjusting or when changing 

accessories, such as blades, bits, cutters, and the like.

DO NOT OVERREACH

Keep proper footing and balance at all times by not overreaching.

ON

(

(

)

)

ON

(

(

)

)

ON

(

(

)

)

ON

(

(

)

)

ON

(

(

)

)

ON

(

(

)

)

ON

(

(

)

)

ON

(

(

)

)

ON

(

(

)

)

ON

(

(

)

)

SECURE WORK

Clamps or a vise should be used to hold work whenever practical. Keeping your hands free 

to operate a power tool is safer.

ON

(

(

)

)

USE PROPER APPAREL

DO NOT wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry that may 

be caught in moving parts. Non-slip footwear is recommended. Wear protective hair cover-

ing to contain long hair.

ON

(

(

)

)

Summary of Contents for 160028









































Reviews: