MJ LED LIGHTNING MJ-1350N, User Manual

Page: 4 / 10

BEAM SPOT WASH (3IN1) 350W BEAM SPOT WASH (3IN1) 350W
SAFE USAGE OF THE PRODUCT
When unpacking and before disposing of the carton, check there is no transportation
damage before using the product. Should there be any damage caused by
transportation, consult your dealer and do not use the apparatus.
The product is for indoor use only, IP20. Use only in dry locations. Keep this device
away from rain and moisture, excessive heat, humidity and dust. Do not allow contact
with water or any other liquids.
The product is not designed or intended to be mounted directly on to inflammable
surfaces
The product is only intended for installation, operation and maintenance by
professional person.
The product must be installed in a location with adequate ventilation, at least 50cm
from adjacent wall surfaces. Be sure that no ventilation slots are blocked.
Do not product the beam onto inflammable surfaces, minimum distance is 12m.
Avoid direct exposure to the light from the lamp. The light is harmful to the eye.
Do not attempt to dismantle or modify the projector in any way.
Electrical connection must only be carried out by qualified personnel.
Before installation, ensure that the voltage and frequency of power supply match the
power requirements of the projector.
It is essential that each projector is correctly earthed and that electrical installation
conforms to all relevant standards.
Do not connect this device to any other types of dimmer apparatus.
Make sure that the power-cord is never crimped or damaged by sharp edges. Never
let the power-cord come into contact with other cables. Only handle the power-cord
by the plug. Never pull out the plug by tugging the power-cord.
Keep the light clean. Do not touch the light glasss with bare hands.
The product should always be installed with a secondary safety fixing. On the
projector base brink, there is a hole for the safety cord provided. It should be attached
as shown in “installing the projector” section.
The lamp used in this projector is a discharge lamp. After switching off don
,
t attempt
to restart the projector until lamp has cooled, this will require approx 15 minutes.
Switching the lamp on and off at short intervals will reduce the life of both the lamp
and the projector. But occasional breaks will prolong the life of the lamp and projector.
Never run the projector without a lamp.
The light shall be changed if it has become damaged or thermally deformed or
reached its life limit.
Shields and lens shall be changed if they have become visibly damaged to such an
extent than their effectiveness is impaired, for example by cracks or deep scratches.
Exterior surface temperatures of the luminaire after 5 minutes operation is 70
°。，
when steady state is achieved 140
°。
There is no user serviceable parts inside the projector, do not open the housing and
never operate the product with the covers removed.
If you have any questions, don’t hesitate to consult your dealer or manufacturer.
★
Always disconnect from the mains, when the device is not in use or
before cleaning it or before attempting any maintenance work !
1
135-195 Slow rotation
196-200 Pattern 1 is slow to fast shake
201-205 Pattern 2 slow to fast shake
206-210 Pattern 3 slow to fast shake
211-215 Pattern 4 slow to fast shake
216-220 Pattern 5 slow to fast shake
221-225 Pattern 6 slow to fast shake
226-230 Pattern 7 slow to fast shake
231-235 Pattern 8 slow to fast shake
236-240 Pattern 10 slow to fast shake
241-245 Pattern 10 slow to fast shake
246-250 Pattern 11 slow to fast shake
CH14 Focusing 0-255 Focus 0% - Focus 100%
CH15
Zoom
0-255 Zoom 0% - Zoom 100%
CH16
Prism 1
(Liner 6-face)
0-255 Prism does not start
128-255 The prism opens
CH17 Prism 1 is rotated
0-127 Prism angle adjustment
128-188 Fast rotation from fast to slow
190-192 stop
193-255 Fast rotation from slow to fast
CH18
Prism 2
(Round 8-face)
0-127 Prism does not start
128-255 The prism opens
CH19 Prism 2 is rotated
0-127 Prism angle adjustment
128-188 Fast rotation from fast to slow
190-192 stop
193-255 Slow rotation from slow to slow
CH 20 Reset
100-105 Light on
200-205 Light off
255 Reset
14