manualshive.com logo in svg

Mitsubishi FX0N-32NT-DP, User Manual, Page: 2 / 58

Share
Download
Mitsubishi FX0N-32NT-DP User Manual Download Page 2

FX0N-32NT-DP Profibus-DP InterfaceUnit

Foreword

•

This manual contains text, diagrams and explanations which will guide the reader in the correct installation
and operation of the FX

0N

-32NT-DP Profibus-DP Interface Unit. It should be read and understood before

attempting to install or use the unit.

•

Further information can be found in the Hardware Manual of the PLC, Programming Manual of the PLC,
MELSOFT GX Configurator-DP Configuration System for Open Networks Software Manual and the manual
of the Profibus-DP master units.

•

If in doubt at any stage of the installation of FX

0N

-32NT-DP Profibus-DP Interface Unit always consult a pro-

fessional electrical engineer who is qualified and trained to the local and national standards which apply to
the installation site.

•

If in doubt about the operation or use of FX

0N

-32NT-DP Profibus-DP Interface Unit please consult the nearest

Mitsubisi Electric distributor.

•

This manual is subject to change without notice. 

Summary of Contents for FX0N-32NT-DP



























































Reviews:

No comments