background image

-

 8 

-

7.  Wired remote control (Optional parts)

The figure below shows the remote control with the cover opened. Note that all the items in the liquid crystal display (LCD) area are shown

for explanation purpose.

Characters displayed with dots in the liquid crystal display (LCD) area are abbreviated.

Pull the cover downwards to open.

* If you press any of the buttons above and “        INVALID OPER” is display, the button has no function.

  But it does not mean a failure.

Ventilation display

Cannot be used.

Displays the settings of the 
weekly timer.

Operation setting display area

Displays setting temperature, airflow 
volume, operation mode and operation 
message.

Operation/check indicator light

During operation: Lit in green
In case of error: Flashing in red

Operation/stop button

This button is used to operate and stop 
the air conditioning system.
Press the button once to operate the 
system and press it once again to stop 
the system.

MODE button

This button is used to change the operation mode.
(The clean operation or allergen clear
operation cannot be selected.) 

FAN SPEED button

This button is used to set the airflow 
volume.
(AUTO, HI POWER or ECONO 
cannot be selected) 

Cannot be used.

LOUVER button

This button is used to operate/stop the
swing louver.
(Up/down swing only)

This button is used to apply the timer operation setting.  

Cannot be used.

Central control display

Displayed when the air conditioning system is 
controlled by centralized remote control.

Timer operation display

Displays the timer operation setting.

These buttons are used to set the 
temperature of the room.

This button is used to set
the timer mode.
(The comfortable timer or sleep
operation cannot be selected.)  

These buttons are used to set 
the timer mode and the time.

Cannot be used.

AIR CON No. button

Display the indoor unit number connected to this 

remote control.

This button is used for indoor unit address setting.

 (”00” appears.)

CHECK button

Display the data of the control.

Cannot be used.

GRILL button

TEST button

VENT button

RESET button

Temperature setting buttons

Timer button

Timer setting buttons

SET button

Weekly timer display

Note (1) The SRK models do not support the buttons and functions displayed in       .

Summary of Contents for SC-BIKN-E





















Reviews: