Mitsubishi Heavy Industries FDC1000KXZWE1 Service Manual Download Page 81

Page: 81 / 183

–

'14 • KX-SM-200

Error code

Remote control:
7-segment display:

LED

Green

Red

Indoor unit

Heat source unit

Content

–

Indoor heat exchanger

temperature thermistor anomaly (ThI-R)

Keeps flashing 1-time flash
Keeps flashing

Stays OFF

1. Applicable model

5. Troubleshooting

All models

Diagnosis

Countermeasure

the connector of

thermistor connected

properly ?

Regarding the characteristics of

the thermistor, see the following chart.

Are

the characteristics

of thermistor OK?

YES

*1 Check several times to prove any poor connection

YES

Temperarture thermistor resistance (kΩ)

Temperature-resistance characteristics of indoor heat

exchanger temperature thermistor (ThI-R1, R2, R3)

5kΩ at 25ºC

Temperature (ºC)

Insert the connector

securely.

Replace thermistor.

(ThI-R)

Replace indoor control.

PCB

2. Error detection method

Detection of anomalously low

temperature (resistance)

of ThI-R1, R2, R3.

3. Condition of error displayed

• If -50ºC or lower is

detected for 5 seconds

continuously, compressor

stops. After 3-minutes delay,

the compressor is restarted

automatically, but if this

anomaly occurs again within

60 minutes after the initial

detection.

• Or if 70ºC or higher is

detected for 5 seconds

continuously.

4. Presumable cause

• Anomalous connection

of indoor heat exchanger

temperature thermistor

• Indoor heat exchanger

temperature thermistor

anomaly

• Indoor control PCB anomaly

Note:

Summary of Contents for FDC1000KXZWE1
























































































































































































Search results

Summary of Contents for FDC1000KXZWE1

Reviews:

Mitsubishi Heavy Industries FDC1000KXZWE1, Service Manual, Page: 81 / 183

Search results

Summary of Contents for FDC1000KXZWE1

Reviews: