Mitsubishi Heavy Industries FDC1000KXZWE1 Service Manual Download Page 109

Page: 109 / 183

–

107

–

'14 • KX-SM-200

Error code

Remote control:
7-segment display:

LED

Green

Red

Indoor unit

Heat source unit

Content

E54

E54-1, 2 *1

High pressure sensor anomaly (PSH)

Low pressure sensor anomaly (PSL)

Keeps flashing

Stays OFF

Keeps flashing

1. Applicable model

5. Troubleshooting

Heat source unit

Diagnosis

Countermeasure

Is anomalous

pressure detected?

Is the

connector of the

sensor inserted properly to

the connector on the heat

source unit control

PCB?

Save data for 30 minutes before stopping in Mente PC.

Reset the power and restart operation.

Check the data for 30 minutes before stopping.

YES

High pressure sensor

output characteristics

Sensor output Black (GND) – White; Output voltage (Black – Red; DC5V)

Pressure (MPa)

Low pressure sensor

output characteristics

YES

Does E54 recur?

Does

the pressure

converted from the

sensor output voltage match the

actual pressure measure

by pressure

gauge?

YES

Output voltage (V)

Check and save the data of

operating conditions.

Check the conditions

whether it occurs

immediately after the

power on or during

operation or stopping.

Check the sensed value.

Insert the connector

securely and restart

operation.

Temporary malfunction by

noise.

Correct if the source of

noise is specified.

Replace sensor (PSH, PSL)

Replace heat source unit

control PCB.

2. Error detection method

Detection of anomalous pressure

(voltage) of PSH or PSL.

Operation range

High pressure : 0-4.15MPa

Low pressure : 0-1.7MPa

3. Condition of error displayed

If anomalous sensor output DC

voltage (0V or lower or 3.49V

or higher) is detected for 5

seconds within 2 minutes to 2

minutes 20 seconds after the

compressor ON.

4. Presumable cause

• Broken sensor harness

• Disconnection of sensor

harness connection (connector)

• Sensor (PSH, PSL) anomaly

• Outdoor control PCB anomaly

• Anomalous installation conditions

• Excessive or insufficient

refrigerant amount

Note:

*1 E54-1: 1-time flash (PSL), E54-2 : 2-time flash (PSH)

[ ]

Summary of Contents for FDC1000KXZWE1
























































































































































































Search results

Summary of Contents for FDC1000KXZWE1

Reviews:

Mitsubishi Heavy Industries FDC1000KXZWE1, Service Manual, Page: 109 / 183

Search results

Summary of Contents for FDC1000KXZWE1

Reviews: