Mitsubishi Electric VS-60HS12U Setup Manual Download Page 9 | Manualshive

Page: 9 / 64

background image

REV 1.0

9

Bas
ic o

pe

rat

io

n

1.3.3

Menus

Basic menu operations

•

The up/down arrow buttons on the remote control
move the yellow cursor to select menus.

•

In a menu with “>” mark on the right, [ENTER] button
shows its lower layer menu. [ESC] button restores the
original upper menu.

•

In a menu with an enter mark on the right, [ENTER]
button confirms or executes the menu.

•

The left/right arrow buttons change the value in a
menu with left/right triangle marks.

•

When values are changed in a menu,

mark

appears. Save the change according to the necessity.
- In WINDOW PRIORITY menu, the mark appears
when an input memory in any of the windows is
changed.
- In INPUT MEMORY menu, the mark appears when
an input memory in the top window is changed.

•

In the menu displaying, [MENU1] button changes the
menu GUI to the simple one. The image area behind
the menu can be observed widely. Re-pressing the
same button restores the original menu.

•

Menus are not displayed when the monitors are
controlled by Wallaby.

TOP menu

The TOP menu is displayed by [MENU1] button on the
remote control in advanced mode. Starting from the
top menu, any lower menus can be choosen.

•

Allocated short-cut buttons also allow you to access
each menu directly, not-through the TOP menu.

INFORMATION menu

It shows various status information on screen.
Short-cut: [DISPLAY] button
Shows the input terminal and input signal
is active or not.

[MENU1] button

«
...
7
8
9
10
11
...
»

Summary of Contents for VS-60HS12U

































































Reviews:

No comments

Related manuals for VS-60HS12U

Brand: Rae Pages: 71

MultiSync XG-1352

Brand: NEC Pages: 38

Brand: Panasonic Pages: 24

TH-58PF20U TENTATIVE

Brand: Panasonic Pages: 3

Brand: Walgreens Pages: 41

YUR.VISION YV24WBH1 -

Brand: YURAKU Pages: 2

YUR.VISION YV216WB2

Brand: YURAKU Pages: 11

YUR.VISION YV19WB1 -

Brand: YURAKU Pages: 2

Brand: Spektrum Pages: 12

Brand: Fametech Pages: 23

InView 2706-PENETx2-SC

Brand: Spectrum Controls Pages: 8

Brand: Azbil Pages: 34

ITRON Telecontrol TC-E

Brand: Allmess Pages: 4

Caneo 43 Hygienic Series

Brand: Captron Pages: 14

Brand: Omron Pages: 16

Brand: Autoleader Pages: 16

Brand: Daewoo Pages: 9

Brand: Daewoo Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands